User manual ADT ENTREPRENEUR 3000EN

[. . . ] 6DIHZDWFK3UR(1 (QWUHSUHQHXU(1 6HFXULW\0DQDJHU(1 6HFXULW\6\VWHPV 8VHU·V*XLGH Meets ADT Security Services Triple Standards Requirements: C LISTED US Standards for Security and Fire Standard for False Alarm Reduction 7 167-0495:110 California State Fire Marshal Approval K5309V2 1/02 1 Model SASW3000EN IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Customer Care Center in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines). EARLY WARNING FIRE DETECTION Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. [. . . ] The 4-digit number (CCCC) that follows this code is the user number that has armed the system. Examples of typical 7-digit pager displays follow. 2. ³ = Reporting of an alarm (911) caused by a fault on zone 4 (0004). ³ = Reporting of a closing­system arming (102)­ by user 5 (0005). ­ 26 ­ 3DJLQJ)HDWXUH $ERXW0DQXDO3DJLQJ Your system may be set up so you can manually send a message to up to four pagers. · Your installer programs the paging function key and the pager phone numbers. · Pressing the paging keys sends the message 9 9 9 ­ 9 9 9 9 to the selected pager. · This message could mean "call home", "call your office", or any other prearranged meaning. · See the Paging chart at the back of this manual for details of the paging setup for your system. (pager no. ) Press and hold the programmed Paging Key for at least 2 seconds (wait for beep), then press the pager number (1-4)* representing the pager intended to receive the message. The recipient, on seeing the 999­9999 message, will understand the prearranged meaning of this signal. * If no number is pressed, the message is sent to pager 1. (-7%61)( 6)%(= 83 %61 English Display: READY Pager Display /DWFK. H\3DJLQJ You can program a schedule that causes a pager report to be sent if the system is not DISARMED by the scheduled time (see Scheduling section, event "03"). For example, a working parent might want a message to be sent to a pager if their child did not arrive home from school and disarm the system by a certain time. If programmed, the message that is sent is: 7 7 7 ­ 7 7 7 7 . ­ 27 ­ 6HFXULW\&RGHV$XWKRULW\/HYHOV $ERXW6HFXULW\&RGHV Your system lets you assign up to 45 different security codes for use by other users. · Only the System Master and Partition Masters can assign user codes to users. · Users are identified by 2-digit user numbers 03-49 and are pre-assigned to either partition 1 or partition 2 (users 01-02 are reserved). · Only the Installer or System Master can change the partitions to which a user is assigned. · In addition to a security code, each user is assigned various system attributes. · User codes can be used interchangeably within a partition when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the guest code described below. Choose a user number from the set of users assigned to the partition in which the user will be operating, and assign a 4-digit security code. Assign other attributes as necessary (see attributes on the next page). NOTE: The factory settings are designed to meet most normal user situations. Therefore, the only step you usually need to do when adding users is assign a user number (from the partition's pre-assigned user numbers) and a security code. $XWKRULW\/HYHO'HILQLWLRQV Authority levels define the system functions a particular user can/cannot perform. Level Title N/A System Master Explanation Reserved for user 02; Can perform all system functions and assign codes in both partitions; can change its own code as follows: Master code + [8] + 02 + new master code + new master code again 0 1 2 3 4 Can only perform security functions in assigned partition. Guest Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (such as a babysitter or cleaner) who has a need to arm/disarm the system only at certain times. [. . . ] To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or address found in your local yellow pages. Service pursuant to the warranty will be furnished only during ADT's normal working hours 8:00A. M. Services rendered outside the normal working hours of ADT are not within the scope of this warranty and any services requested to be performed at such times shall be charged for at ADT's then applicable rates for labor and material. This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on the system. [. . . ]