User manual ADT SAFEWATCH PLUS

[. . . ] Table of Contents * System Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ARMING Arming The System Prior To Leaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Arming The System Without Leaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Other programming functions may be possible that are not detailed in this section. Consult your security representative for a list of the user programmable features of your system. WARNING: Do not attempt to program the system unless you have been properly trained on programming procedures and you are sure that you fully understand thlsopwatlon. USER CODES Your system may be programmed to accept up to five regular User Codes and one Muster User Code. The Master User Code (code 1) performs all of the User Code functions plus allows access to the programming mode. User Code 6 may be programmed as a Temporary User Code with a limited number of valid uses, after which it becomes inoperable. This code may be assigned to a maintenance person, maid, or anyone who you would like to be able to arm and disarm the system for a selected number of times without having to reveal your regular code. A Determine your desired new User Code or Master User Code sequence. If you make an error while programming, press the " * " key five times and start over from step 1. WARNING: Pressing the " # " or l4 * " key while programmlng a code may result In Improper code operation, therefore you MUST return to step 1 when an error Is made. 0 To Change A User Code 1. The READY and ARMED indicators will blink alternately and the other eight indicators will blink repeatedly when the programming mode is successfully entered (see note + on page C). 4. Press a key (Z-6) which corresponds to the User Code you wish to program, or press key 1 to change the Master User Code, then press the " # " key. For example, press 1, then # to change the Master User Code, or 4 then # to program User Code 4, etc. After the fourth digit is entered, the control station will emit one short beep followed by one long beep then the system will exit the programming mode automatically. The READY and ARMED indicators will blink alternately and the other eight indicators will blink in sequence with each other when the programming mode is successfully entered (see note $). Press key 1, then key 0, then # which instructs the control that you wish to delete a code. B An optional feature of your system allows you to assign a certain number of valid uses to User Code 6. After the code has been used the programmed amount of times, it automatically becomes disabled. This code may be assigned to a maintenance person, a maid, or anyone who you would like to be able to arm and disarm the system for a selected number of times without having to give out your regular code. It can be re-enabled by programming in another number indicating how many times that it can be used. It will not be necessary to re-program the actual code unless changing the code itself is desired. The READY and ARMED indicators will blink alternately and the other eight indicators will blink in sequence with each other when the programming mode is successfully entered (see note *). Press key 6, then # to instruct the control that you wish to program the desired code sequence for User Code 6. After the fourth digit is entered, the control station will emit one short beep followed by one long beep then the system will exit the programming mode automatically. Press keys 7 plus # to instruct the control that you wish to program the number of valid uses for User Code 6. [. . . ] 16 Glossary Alarm Memory: A history of the alarm that last occurred. Control Panel: The main system electronics housed in a metal enclosure. Control Station: The remote station used to enter instructions to the control panel such as to arm, disarm amd bypass. Delay Zone: Zone which allows a programmable amount of time to enter and disarm the system without activating an alarm. [. . . ]