User manual ADT SECURITY MANAGER 2000

[. . . ] Security System User's Manual Security Manager 2000 N75276V2 4/99 Ref. S1632 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to an alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines). About This Manual This manual is a step-by-step guide that will acquaint you with the system's features and benefits. [. . . ] Note that the master (primary) user of the system is the only one who can assign codes to secondary (or temporary) users, and is user number 02; user number 01 is reserved for the installer of the system. All codes can be used interchangeably when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the babysitter code described below. Babysitter Code This code can be used to arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (such as a babysitter) who has a need to arm/disarm the system only at certain times. The user of this code should not use the Quick Arming feature described below. Duress Code This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Customer Care Center of your situation, if that service has been provided. Important: This code is useful only when the system is connected to the Customer Care Center. Note that if "Quick Arming" was programmed by the installer, the # key can be pressed in place of the security code when arming the system. If so programmed, the A and B keys on a touchpad can be used for single-button arming AWAY or STAY, respectively. 25 Quick Arming and Single-Button Arming SECURITY CODES (Continued) To Add a User or Change a User's Code Important: Temporary users of the system (e. g. , babysitters, cleaning staff) should not be shown how to use any system function they do not need to know, such as bypassing protection zones for example. Sequential key depressions for all steps in a procedure must be made within 2 seconds of one another, or else the entire entry is aborted and must be repeated from its beginning (e. g. , perform steps 1, 2, and 3 below with no delay between steps). CODE Changing your Master Code Follow this procedure: Enter your existing Master code + [8] + [0][2] + new Master code + new Master code again. 1. + 8 Enter master code, then press CODE key. Example: 7 2 9 6 (Master Code) then press the CODE key. 2. Enter the 2-digit User Number (03-16) for the user you are adding or changing. CODE (User's Code) Enter user's code. Example: 7 2 9 6 To Delete a User 1. + 8 (Master Code) then press the CODE key. 2. (User Number) 3. ----------- Enter user number. Enter the 2-digit User Number (03-16) for the user whose code you are deleting. Wait (about 3 seconds) until the touchpad beeps once before pressing any other key. 26 TESTING THE SYSTEM (TO BE CONDUCTED WEEKLY) Using the 5 TEST Key The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The touchpad sounds a single beep every 40 seconds as a reminder that the system is in the Test mode. N o t e : An alarm message will not be sent to your Customer Care Center during the following tests. The READY indicator light should come on if all zones are intact (i. e. , all protected windows, doors, etc. are closed. AC *** DISARME D *** RE ADY TO ARM ENGLISH DISPLAY TOUCHPAD TEST CUSTOM DISPLAY TOUCHPAD 2. + 5 Enter the security code, then press TEST key. Example: 7 2 9 6 (Security Code) then press the TEST key. 3. Open each protected door and window in turn and listen for three beeps from the touchpad. Identification of each faulted protection point should appear on the display. [. . . ] Labor and material required to repair or replace such defective components or to make mechanical adjustments to the system will be free of charge for a period of 90 days following the completion of the original installation. This warranty is extended only to the original consumer purchaser of the system and may be enforced only by such person. To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or address found in your local yellow pages. Service pursuant to the warranty will be furnished only during ADT's normal working hours 8:00A. M. [. . . ]