User manual ADT SERIES 4250

[. . . ] USER GUIDE SERIES 4250 AUDIO ALARM CONFIRMATION SYSTEM CONTROL UNIT CONTENTS Page INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Security conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Full Set (Fully armed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Part Set (Partially armed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 7) Leave the premises immediately via the designated Exit/ Entry route, close and lock the final door and operate the Final Exit Terminator switch. If the Exit Terminator switch is not operated the system will automatically set after the predetermined exit time. Part-Set Full-Set 4) The Keypad LCD Display will change and you will be prompted to enter your x digit user code and press the enter button. 3) Press FULL SET key 8 8. The keypad then beeps twice and the buzzer stops to confirm that the system is set. SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET The keypad display text will indicate the reason which prevents the user selecting FULL SET. Zone fault conditions If alarm devices, other than the final door or Exit/Entry alarm devices are open or activated then this will prevent the setting procedure being started. If a fault exists when attempting to set the system the keypad display will show a message indicating where the fault is located. For example, the following display, indicates the system remains UNSET due to a fault in zone 05. Note: A zone is an area such as a room or corridor that is monitored by a device such as a movement detector, door contacts etc. 9 If more than one fault exists by pressing the Next key other faults will be displayed in sequence. When the fault(s) indicated have been cleared, carry out the setting procedure for FULL SET. If the fault(s) cannot be immediately cleared and the user needs to set the system, the faulty zone(s) can be omitted from the system by the user with a master code (page 35). This facility is subject to insurance company agreement. Omit key Next key SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Incorrect code entry If the incorrect code is entered during selection procedure the keypad LCD Display will show. After 3 attempts to enter your code the system will refuse further setting attempts for two minutes and this condition is reported to the Alarm Receiving Centre. After the two minutes have elasped a further 3 attempts may be made. Retry key 10 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Deviation from the Correct Exit Procedure Deviating from the designated Exit route when the countdown period has started will cause the keypad exit bleep to change to a continuous tone. closing any doors on the wrong route will cause the keypad bleeper tone to change to the normal intermittent bleep and you will be able to exit normally. If any zones having been entered by deviating from the exit route are not restored, e. g. doors not closed, within the set exit time the keypad display will show: The FAILED TO EXIT condition will be reported to the Alarm Receiving Centre and the audible tone will continue to sound until the x digit user code is entered. Eliminate the fault and repeat the FULL SET procedure. 11 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PROBLEMS WHEN SELECTING FULL SET Failure to complete exit procedure If during the FULL SET procedure the user fails to exit the premises with in the set exit time the setting fault condition will be indicated on the keypad LCD as shown: The FAIL TO EXIT condition is reported to the Alarm Receiving Centre and the keypad audible tone will continue to sound. 12 SETTING THE SYSTEM (TURNING THE SYSTEM ON) PART SET (Partially armed) The PART SET condition allows the alarm system to be armed (set) in certain zones of the protected premises while the remainder of the premises are occupied. Two PART SET selections are available as follows: Delay selection: This feature is selected when access to the non-alarmed (occupied) area is via a protected part of the premises. When the PART SET delay selection is set at the keypad there is a time delay to allow the user to leave the protected area. On entering the protected area by the normal entry route there is a similar time delay to allow the user to key in the x digit user code to UNSET (switch off) the system. An example of using this selection is a house with the downstairs protected and the upstairs occupied but the occupants require access to the keypad to PART SET or UNSET the system. [. . . ] If a fault condition arises, this will be indicated audibly in the same way as a tamper condition, and confirmed by the keypad display, e. g. : Similary, to silence the audible warning, the x digit user code is entered on the keypad, which results in the display indicating: The display indicator remains until the fault is cleared. If the fault remains and and reason is unknown then contact the Alarm Company Service Department. 28 TEST SIGNAL Following prior notification a test signal can be sent to the Alarm Receiving Centre for the following purposes: 1) Confirming the operational status of the system. To send a test signal, the system must be in the UNSET condition as shown by the display: Key in the x digit user code and press the enter key: Press the * key on the keypad and the display will show: 29 Call key History Key TEST SIGNAL Press the Call key. The display will show: Yes key No key Press the YES key to send the test signal, the Alarm Receiving Centre Operator will notify the user as appropriate. 30 CHIME MODE (OPTIONAL FEATURE) The Chime mode option causes the keypad to bleep if a protected area is violated when the system is UNSET (switched off) or is PART SET. [. . . ]