User manual ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 CLI REFERENCE GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ALCATEL-LUCENT OMNISWITCH 6800-6850-9000. We hope that this ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 user guide will be useful to you.
You may also download the following manuals related to this product:
ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 SWITCH MANAGEMENT GUIDE (4187 ko)
ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 NETWORK CONFIGURATION GUIDE (12492 ko)
ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 ADVANCED ROUTING CONFIGURATION GUIDE (6273 ko)
Manual abstract: user guide ALCATEL-LUCENT OMNISWITCH 6800-6850-9000CLI REFERENCE GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] D June 2007
OmniSwitch CLI Reference Guide
www. alcatel-lucent. com
This user guide documents release 6. 1. 5 of the OmniSwitch 6800 Series, OmniSwitch 6850 Series, and OmniSwitch 9000 Series and release 6. 2. 1 of the OmniSwitch 6850 Series. The functionality described in this guide is subject to change without notice.
Copyright © 2007 by Alcatel-Lucent. This document may not be reproduced in whole or in part without the express written permission of Alcatel-Lucent. Alcatel-Lucent® and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. [. . . ] 16-byte text string.
Defaults
The default authentication string is a null string.
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
Regardless of which authentication type is used (simple or MD5), both switches on either end of a link must share the same password.
Examples
-> ip rip interface 172. 22. 2. 115 auth-key nms
Release History
Release 5. 1; command was introduced. Release 6. 2. 1; ip_address parameter deprecated.
Related Commands
ip rip interface auth-type Configures the type of authentication that will be used for the RIP interface.
MIB Objects
rip2IfConfTable rip2IfConfAddress rip2IfConfAuthKey
page 29-34
OmniSwitch CLI Reference Guide
June 2007
RIP Commands
ip rip update-interval
ip rip update-interval
Configures the time interval during which RIP routing updates are sent out. ip rip update-interval seconds
Syntax Definitions
seconds The RIP routing update interval, in seconds. The valid range is 1120.
Defaults
parameter seconds default 30
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
The update interval value must be less than or equal to one-third the invalid interval value.
Examples
-> ip rip update-interval 45
Release History
Release 6. 1. 5; command was introduced.
Related Commands
show ip rip Displays the RIP status and general configuration parameters (e. g. , forced hold-down timer).
MIB Objects
alaProtocolRip alaRipUpdateInterval
OmniSwitch CLI Reference Guide
June 2007
page 29-35
ip rip invalid-timer
RIP Commands
ip rip invalid-timer
Configures the RIP invalid timer value that defines the time interval during which a route will remain active in Routing Information Base (RIB) before moving to the invalid state. ip rip invalid-timer seconds
Syntax Definition
seconds The RIP invalid timer value, in seconds. The valid range is 3360.
Defaults
parameter seconds default 180
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
The invalid time interval value must be three times the update interval value.
Examples
-> ip rip invalid-timer 270
Release History
Release 6. 1. 5; command was introduced.
Related Commands
show ip rip Displays the RIP status and general configuration parameters (e. g. , forced hold-down timer).
MIB Objects
alaProtocolRip alaRipInvalidTimer
page 29-36
OmniSwitch CLI Reference Guide
June 2007
RIP Commands
ip rip garbage-timer
ip rip garbage-timer
Configures the RIP garbage timer value that defines the time interval, which must elapse before an expired route is removed from the RIB. ip rip garbage-timer seconds
Syntax Definition
seconds The RIP garbage timer value, in seconds. The valid range is 0180.
Defaults
parameter seconds default 120
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
During the RIP garbage interval, the router advertises the route with a metric of INFINITY (i. e. , 16 hops).
Examples
-> ip rip garbage-timer 180
Release History
Release 6. 1. 5; command was introduced.
Related Commands
show ip rip Displays the RIP status and general configuration parameters (e. g. , forced hold-down timer).
MIB Objects
alaProtocolRip alaRipGarbageTimer
OmniSwitch CLI Reference Guide
June 2007
page 29-37
ip rip holddown-timer
RIP Commands
ip rip holddown-timer
Configures the RIP hold-down timer value that defines the time interval during which a route remains in the hold-down state. ip rip holddown-timer seconds
Syntax Definition
seconds The hold-down time interval, in seconds. The valid range is 0120.
Defaults
parameter seconds default 0
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
When RIP detects a route with higher metric than the route in the RIB, the route with the higher metric goes into the hold-down state. The route updates with a metric of INFINITY are rejected.
Examples
-> ip rip holddown-timer 10
Release History
Release 6. 1. 5; command was introduced.
Related Commands
show ip rip Displays the RIP status and general configuration parameters (e. g. , forced hold-down timer).
MIB Objects
alaProtocolRip alaRipHolddownTimer
page 29-38
OmniSwitch CLI Reference Guide
June 2007
RIP Commands
show ip rip
show ip rip
Displays the RIP status and general configuration parameters (e. g. , forced hold-down timer). show ip rip
Syntax Definitions
N/A
Defaults
N/A
Platforms Supported
OmniSwitch 6800, 6850, 9000
Usage Guidelines
N/A
Examples
-> show ip rip Status Number of routes Host Route Support Route Tag Update interval Invalid interval Garbage interval Holddown interval Forced Hold-Down Timer = = = = = = = = = Enabled 9 Enabled 42 30 180 120 0 0
output definitions Status Number of routes Host Route Support Route Tag Update interval Invalid interval Garbage interval RIP status (Enabled or Disabled). Indicates whether or not RIP can add host routes (routes with a 32-bit mask) to the RIP table. Default is 120.
OmniSwitch CLI Reference Guide
June 2007
page 29-39
show ip rip
RIP Commands
output definitions Holddown interval Forced Hold-Down Timer The hold-down time interval, in seconds. Default is 0.
Release History
Release 5. 1; command was introduced. Release 6. 1. 5; new fields added.
Related Commands
ip rip status ip rip force-holddowntimer ip rip update-interval ip rip invalid-timer Enables/disables RIP routing on the switch. Configures the interval during which a RIP route remains in the forced hold-down state. Configures the time interval during which RIP routing updates are sent out. Configures the RIP invalid timer value that defines the time interval during which a route will remain active in Routing Information Base (RIB) before moving to the invalid state. Configures the RIP garbage timer value that defines the time interval, which must elapse before an expired route is removed from the RIB. Configures the RIP hold-down timer value that defines the time interval during which a route remains in the hold down state.
ip rip garbage-timer
ip rip holddown-timer
MIB Objects
alaProtocolRip alaRipProtoStatus alaRipRouteNumber alaRipHostRouteSupport alaRipRedistRouteTag alaRipUpdateInterval alaRipInvalidTimer alaRipGarbageTimer alaRipHolddownTimer alaRipForceHolddownTimer
page 29-40
OmniSwitch CLI Reference Guide
June 2007
RIP Commands
show ip rip routes
show ip rip routes
Displays the RIP routing database. show ip rip routes [ip_address ip_mask]
Syntax Definitions
ip_address ip_mask 32-bit IP address. [. . . ] In case of any termination of the Software License Agreement between Alcatel-Lucent and Licensee, Licensee shall immediately return the EMWEB Product and any back-up copy to AlcatelLucent, and will certify to Alcatel-Lucent in writing that all EMWEB Product components and any copies of the software have been returned or erased by the memory of Licensee's computer or made non-readable.
J. RSA Security Inc.
Provided with this product is certain security software ("RSA Software") licensed from RSA Security Inc. PROVIDES RSA SOFTWARE "AS IS" WITHOUT ANY WARRANTY WHATSOEVER. DISCLAIMS ALL WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, AS TO ANY MATTER WHATSOEVER INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.
K. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ALCATEL-LUCENT OMNISWITCH 6800-6850-9000
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ALCATEL-LUCENT OMNISWITCH 6800-6850-9000 will begin.