User manual ART DMV-PRO

[. . . ] 7KH$57 3URJUDPPDEOH 'LJLWDO (IIHFWV 3URFHVVRU TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AC Power Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Audio Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the encoder and turn to the right to view these parameters. CC Channel: This parameter sets the channel that the current controller assignment will receive MIDI commands over. The CC Channel's range is from 1 to 16. MIDI CC Number: This parameter sets the actual MIDI controller that will modify the current controller assignment's parameter. MIDI CC Number's options are OFF (don't receive any information), 1 through 119, Note On, Aftertouch, and Pitchbend. Also, any external MIDI action on this controller's MIDI channel will automatically set the MIDI CC Number. (See page 53 for a listing of standard MIDI controller numbers. ) Mode When Note On, Velocity, or Aftertouch is selected as the MIDI CC Number, another parameter--Mode-- becomes available to help fine-tune the controller's operation. Mode sets the way a note on, velocity, or aftertouch message is interpreted; its two choices are Toggle or Continuous. If set to Continuous, the - 21 - controller's value linearly corresponds to the key, velocity, or aftertouch value being played. For example, if MIDI CC Number was set to Note On and Mode was set to Continuous, then the controller's value would equal the key number played. Key, Velocity, or AT Value If Mode is set to Toggle, a second parameter becomes available to set the key, velocity, or aftertouch value that will toggle between the controller values 0 and 127. For example, if MIDI CC Number was set to Note On and Mode was set to Toggle, the next available parameter is Key. If this is set to C4, the value that the controller assignment receives will be 0 until a C4 is played. Once a C4 is played, the value goes to 127 until it is released and the value goes to 0 again. Parameter: This control sets the parameter that a received MIDI controller event will change; it can be set to any of the effect's parameters. Value Low Range This control sets the selected parameter's value when a MIDI value of 0 is received. The range of this control is dependent on the selected parameter's range. Val. High Range This control sets the selected parameter's value when a MIDI value of 127 is received and like Value Low Range, its range depends on the parameter's range. Any MIDI values between 0 and 127 will produce parameter values that are scaled between the Value Low Range and Val. High Range, thus creating MIDI control that acts "upside down. " That is, a low incoming value can have a greater effect than a high one. After you have edited the parameters for one controller assignment, you may wish to edit one of the effect's other three. Make sure the encoder is selecting parameters (i. e. , the Selection Arrow is on the top line) and turn it to the left until the LCD again reads [ -T20-++$0]. Push the encoder and turn it to select one of the other controllers (a, b, c, or d) and similarly adjust their parameters. Finally, save your MIDI edits by saving the preset: Press Store, select a preset number to overwrite, and press Store again to confirm the save. If you instead press any button other than Store, you will return to Preset mode and the MIDI edits will not be saved, though they will remain active until you change presets. - 22 - TUTORIAL 4: ADVANCED APPLICATIONS The Smart Encoder: The Smart EncoderTM functions allow you to perform real-time tasks, such as tapping in new delay times or spinning up and down the rotary effect, by pressing the Edit and Encoder buttons. Using the encoders this way is called "smart" because parameters can be automatically changed, instead of by having to manually scroll through a series of menus and values. The table below lists all of the Smart Encoder functions and the effect-classes they are available from. Assigning the functions is explained in the next section. FUNCTION: Reverb Test Tap Delay Time Delay Hold Rotary Spin HI/LO AVAILABILITY: All Reverb Classes All Delay Classes Except Mic Placement All Delay Classes Except Mic Placement All Rotary Classes except Auto Switch and Dynamic Reverb With reverb effects, the Smart Encoder can be used to trigger a reverb test impulse. A reverb impulse is a short, all-frequency burst for auditioning a reverb's sound. [. . . ] System status response from DMV-PRO. Parameter Exchange Unit Status The SysEx message to make the DMV-PRO dump all presets is: F0 1A 0x 21 4B F7 Other MIDI Notes The DMV-PRO ignores inbound Active Sensing messages. The System Reset message is ignored. - 52 - MIDI CONTROLLERS AND NUMBERS Here's a list of MIDI Controllers and their numbers, which may help to avoid conflicts if you control the DMV-PRO and other MIDI gear in the same setup. The following table lists hexadecimal numbers, their equivalent decimal numbers, and the common uses for these controller numbers in MIDI. The DMV-PRO's default controller parameters are intended to work with the default values of A R T's foot controller, the X-15. [. . . ]