User manual ASROCK 4CORE1333-GLANM

[. . . ] please refer to below steps for the software setting of Multi-Streaming. For Windows® XP: After restarting your computer, you will find "Mixer" tool on your system. please select "Mixer ToolBox" , click "Enable playback multi-streaming" , and click "ok". Choose "2CH" or "4CH" and then you are allowed to select "Realtek HDA Primary output" to use Rear Speaker and Front Speaker, or select "Realtek HDA Audio 2nd output" to use front panel audio. [. . . ] When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws!775-Pin Socket Overview Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Disengaging the lever by depressing down and out on the hook to clear retention tab. Pin1 orientation key notch orientation key notch Pin1 alignment key alignment key For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket. Carefully place the CPU into the socket by using a purely vertical motion. Remove PnP Cap (Pick and Place Cap): Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap. This cap must be placed if returning the motherboard for after service. Secure load lever with load plate tab under retention tab of load lever. For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink. Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR2 DIMM pair in the slots of the same color. In other words, you have to install identical DDR2 DIMM pair in Dual Channel A (DDRII_1 and DDRII_3; Yellow slots; see p. This motherboard also allows you to install four DDR2 DIMMs for dual channel configuration, and please install identical DDR2 DIMMs in all four slots. DDRII_1 (Yellow Slot) 2 memory modules SS 2 memory modules DS 2 memory modules X 2 memory modules X 4 memory modules SS If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in the slots of the same color. In other words, install them either in the set of yellow slots (DDRII_1 and DDRII_3), or in the set of orange slots (DDRII_2 and DDRII_4). If only one memory module or three memory modules are installed in the DDR2 DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory Technology. If a pair of memory modules is NOT installed in the same Dual Channel, for example, installing a pair of memory modules in DDRII_1 and DDRII_2, it is unable to activate the Dual Channel Memory Technology . [. . . ] This motherboard supports Untied Overclocking Technology, which means during overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter "Overclock Mode" option of BIOS setup to set the selection from [Auto] to [CPU, PCIE, Async. Therefore, CPU FSB is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment. Please refer to the warning on page 6 for the possible overclocking risk before you apply Untied Overclocking Technology. [. . . ]