User manual ASROCK 775I65G R3.0

[. . . ] 775i65G User Manual Version 3. 0 Published June 2012 Copyright©2012 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p. 10 No. 18) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. 6) PIN1 IDE1 PIN1 IDE2 connect the black end connect the blue end to the IDE devices to the motherboard 80-conductor ATA 66/100 cable Note: If you use only one IDE device on this motherboard, please set the IDE device as “Master”. Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). 9) SATA2 SATA1 These two Serial ATA (SATA) connectors support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. Serial ATA (SATA) Data Cable 19 USB 2. 0 Header (9-pin USB67) (see p. 10 No. 16) 1 USB_PWR P-7 P+7 GND DUMMY GND P+6 P-6 USB_PWR The I/O panel accommodates 6 default USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This USB4_5 connector is shared with the USB 2. 0 ports 4, 5 on the I/O panel. When using the front panel USB ports by attaching the front panel USB cable to this connector (USB4_5), the USB ports 4, 5 on the I/O panel will not be able to function. This header supports an optional wireless transmitting and receiving infrared module. Shared USB 2. 0 Header (9-pin USB4_5) (see p. 10 No. 26) USB_PWR P-5 P+5 GND 1 USB_PWR P-4 P+4 GND DUMMY Infrared Module Header (5-pin IR1) (see p. 10 No. 17) 1 IRTX +5VSB DUMMY GND IRRX Internal Audio Connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 10 No. 20) AUX1 CD1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. Front Panel AC’97 Audio Header (8-pin AUDIO1) (see p. 10 No. 21) 1 AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC GND BACKOUT-R BACKOUT-L AUX-L GND GND AUX-R CD-L GND GND CD-R 20 1. +5VA is used for audio power only, please don’t connect it to any other power, such as USB. HD (Azalia) audio front panel and AC’97 audio front panel have different pin-definition. Incorrect connection of the audio front panel and the front panel audio header may cause permanent damage to this motherboard. System Panel Header (9-pin PANEL1) (see p. 10 No. 12) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 10 No. 14) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Power LED Header (3-pin PLED1) (see p. 10 No. [. . . ] Configuration options: [IRQ5] and [IRQ7]. 37 3. 3. 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration USB Controller USB 2. 0 Support Legacy USB Support [Enabled] [Enabled] [Auto] To enable or disable the onboard USB controllers. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. USB Controller Use this item to enable or disable the use of USB controller. USB 2. 0 Support Use this item to enable or disable the USB 2. 0 support. Legacy USB Support Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard, . . . Or you may select [Auto] so that the system will start to auto-detect; if there is no USB device connected, “Auto” option will disable the legacy USB support. 38 3. 4 Hardware Health Event Monitoring Screen In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage. Main Advanced BIOS SETUP UTILITY Boot H/W Monitor Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature CPU_FAN1 Speed CHA_FAN1 Speed Vcore + 3. 30V + 5. 00V + 12. 00V CPU Quiet Fan : 45 C / 98 F : 31 C / 87 F : 2463 RPM : N/A : : : : 1. 384V 3. 306V 5. 067V 11. 890V [Disabled] F1 F9 F10 ESC Select Screen Select Item General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. CPU Quiet Fan This item allows you to identify the temperature of CPU fan. [. . . ]