User manual ASROCK 775XFIRE-ESATA2+

[. . . ] 775XFire-eSATA2+ User Manual Version 1. 0 Published April 2006 Copyright©2006 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Please connect a CPU fan cable to this connector and match the black wire to the ground pin. CPU Fan Connector (4-pin CPU_FAN1) (see p. 11 No. 6) GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL 27 ATX Power Connector (20-pin ATXPWR1) (see p. 11 No. 33) Please connect an ATX power supply to this connector. ATX 12V Connector (4-pin ATX12V1) (see p. 11 No. It is not necessary to use this connector, but please connect it with a hard disk power connecor when two graphics cards are plugged to this motherboard at the same time. Connect a Game cable to this header if the Game port bracket is installed. SLI/XFIRE Power Connector (4-pin SLI/XFIRE_POWER1) (see p. 11 No. 3) SLI/XFIRE_POWER1 Game Port Header (15-pin GAME1) (see p. 11 No. 26) 1 +5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN +5V JAB2 JAY GND GND JAX JAB1 +5V HDMI_SPDIF Header (3-pin HDMI_SPDIF1) (see p. 11 No. 29) 1 GND SPDIFOUT +5V HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the black end (A) of HDMI_SPDIF cable to the HDMI_SPDIF header on the motherboard. Then connect the white end (B or C) of HDMI_SPDIF cable to the HDMI connector of HDMI VGA card. white end (3-pin) SPDIFOUT GND blue black HDMI_SPDIF Cable (Optional) C B A A. white end (2-pin) SPDIFOUT GND blue black 28 USB Bracket This USB bracket can support 2 additional USB 2. 0 ports besides the I/O panel. Please connect the blue connector on the cable of this USB bracket to the USB 2. 0 header (USB23, USB45, or USB67) and fasten the USB bracket to the chassis with screws. 29 2. 11 HDMI_SPDIF Header Connection Guide HDMI (High-Definition Multi-media Interface) is an all-digital audio/video specification, which provides an interface between any compatible digital audio/ video source, such as a set-top box, DVD player, A/V receiver and a compatible digital audio or video monitor, such as a digital television (DTV). A complete HDMI system requires a HDMI VGA card and a HDMI ready motherboard with a HDMI_SPDIF header. This motherboard is equipped with a HDMI_SPDIF header, which provides SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/projector/LCD devices. To use HDMI function on this motherboard, please carefully follow the below steps. Install the HDMI VGA card to the PCI Express Graphics slot on this motherboard. Connect the black end (A) of HDMI_SPDIF cable to the HDMI_SPDIF header (HDMI_SPDIF1, yellow, see page 11, No. 29) on the motherboard. Make sure to correctly connect the HDMI_SPDIF cable to the motherboard and the HDMI VGA card according to the same pin definition. For the pin definition of HDMI_SPDIF header and HDMI_SPDIF cable connectors, please refer to page 28. For the pin definition of HDMI_SPDIF connectors on HDMI VGA card, please refer to the user manual of HDMI VGA card vendor. Incorrect connection may cause permanent damage to this motherboard and the HDMI VGA card. Step 3. Connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF connector of HDMI VGA card. [. . . ] If you set this option as [Enabled], you will find the items "Target CPU Temperature ( C)", "Tolerance ( C)", and "Minimun Fan Speed" appear to allow you adjusting them. Target CPU Temperature ( C) The target temperature will be between 45 C and 65 C. Tolerance ( C) The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C. You can freely adjust the target fan speed according to the target CPU temperature that you choose. [. . . ]