User manual ASROCK 890FX DELUXE4

[. . . ] 890FX Deluxe4 User Manual Version 1. 0 Published July 2010 Copyright©2010 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly. Power LED Header (3-pin PLED1) (see p. 12 No. 22) 1 PLEDPLED+ PLED+ Please connect the chassis power LED to this header to indicate system power status. Please connect the chassis speaker to this header. Chassis Speaker Header (4-pin SPEAKER 1) (see p. 12 No. 23) 1 SPEAKER DUMMY DUMMY +5V Chassis and Power Fan Connectors (4-pin CHA_FAN1) (see p. 12 No. 44) GND FAN_SPEED_CONTROL +12V CHA_FAN_SPEED (3-pin CHA_FAN2) (see p. 12 No. 39) Please connect the fan cables to the fan connectors and match the black wire to the ground pin. CHA_FAN1/2/3 fan speed can be controlled through BIOS or OC Tuner utility. CPU Fan Connectors (4-pin CPU_FAN1) (see p. 12 No. 7) 1234 Please connect the CPU fan cable to the connector and match the black wire to the ground pin. 30 Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3. Pin 1-3 Connected 3-Pin Fan Installation (3-pin CPU_FAN2) (see p. 12 No. 11) 12 24 Please connect an ATX power supply to this connector. 1 13 Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13. 12 24 20-Pin ATX Power Supply Installation 1 13 ATX 12V Power Connector (8-pin ATX12V1) (see p. 12 No. 4) 1 5 4 8 Please connect an ATX 12V power supply to this connector. Though this motherboard provides 8-pin ATX 12V power connector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 5. 1 4 4-Pin ATX 12V Power Supply Installation 5 8 IEEE 1394 Header (9-pin FRONT_1394) (see p. 12 No. 14) 1 RXTPAM_0 GND RXTPBM_0 +12V GND +12V RXTPBP_0 GND RXTPAP_0 Besides one default IEEE 1394 port on the I/O panel, there is one IEEE 1394 header (FRONT_1394) on this motherboard. This IEEE 1394 header can support one IEEE 1394 port. 31 Serial port Header (9-pin COM1) (see p. 12 No. 30) 1 RRXD1 DDTR#1 DDSR#1 CCTS#1 This COM1 header supports a serial port module. RRI#1 RRTS#1 GND TTXD1 DDCD#1 HDMI_SPDIF Header (2-pin HDMI_SPDIF1) (see p. 12 No. 45) 1 GND SPDIFOUT HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header. This front USB 3. 0 panel can support 2 additional USB 3. 0 ports besides the I/O panel. Please connect the light blue connector on the cable of this front USB 3. 0 panel to the USB 3. 0 header (USB3_1_2) and fasten the front USB 3. 0 panel to the chassis with the bundled six screws. Front USB 3. 0 Panel 32 2. 9 Smart Switches This motherboard has three smart switches: power switch, reset switch and clear CMOS switch, allowing users to quickly turn on/off or reset the system or clear the CMOS values. 26) Power Switch is a smart switch, allowing users to quickly turn on/off the system. [. . . ] USB 3. 0 Controller Use this item to enable or disable the use of USB 3. 0 controller. USB Keyboard/Remote Power On Use this item to enable or disable USB Keyboard/Remote Power On on the system. USB Mouse Power On Use this item to enable or disable USB Mouse Power On on the system. 62 3. 5 Hardware Health Event Monitoring Screen In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage. BIOS SETUP UTILITY Boot Advanced H/W Monitor Main OC Tweaker Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature CPU Fan 1 Speed CPU Fan 2 Speed Chassis Fan 1 Speed Chassis Fan 2 Speed Chassis Fan 3 Speed Power Fan Speed Vcore + 3. 30V + 5. 00V + 12. 00V CPU Fan Setting Chassis Fan Setting : 37 C / 98 F : 27 C / 80 F : : : : : : : : : : 4722 RPM 4722 RPM N/A N/A N/A N/A 1. 216V 3. 248V 5. 136V 12. 091V Enable/Disable CPU Quiet Fan Function. F1 F9 F10 ESC Select Screen Select Item General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. CPU Fan 1 & 2 Setting This allows you to set the CPU fan 1 & 2 speed. The default is value [Full On]. 63 3. 6 Boot Screen In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. Main OC Tweaker BIOS SETUP UTILITY Advanced H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD / DVD: 3S - CD - ROM C] [USB] Configure Settings during System Boot. Enter F1 F9 F10 ESC Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2005, American Megatrends, Inc. 3 . [. . . ]