User manual ASROCK 939A790GMH

[. . . ] 939A790GMH User Manual Version 1. 0 Published July 2010 Copyright©2009 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!26) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. 9) PIN1 IDE1 connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors SATAII_1 (PORT 0) SATAII_2 (PORT 1) SATAII_3 (PORT 2) SATAII_4 (PORT 3) see p. 11, No. 17) Serial ATA (SATA) Data Cable (Optional) SATAII_5 (PORT 4) (SATAII_1 (PORT 0): These five Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3. 0 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on this motherboard. 24 USB 2. 0 Headers (9-pin USB8_9) (see p. 11 No. 10) 1 USB_PWR P-9 P+9 GND DUMMY GND P+8 P-8 USB_PWR Besides four default USB 2. 0 ports on the I/O panel, there are three USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. (9-pin USB6_7) (see p. 11 No. 11) USB_PWR P-7 P+7 GND DUMMY 1 GND P+6 P-6 USB_PWR (9-pin USB4_5) (see p. 11 No. 12) USB_PWR P-5 P+5 GND DUMMY 1 GND P+4 P-4 USB_PWR Print Port Header (25-pin LPT1) (see p. 11 No. 25) 1 AFD# ERROR# PINIT# SLIN# GND SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# This is an interface for print port cable that allows convenient connection of printer devices. Infrared Module Header (5-pin IR1) (see p. 11 No. 30) 1 IRTX +5V DUMMY GND IRRX This header supports an optional wireless transmitting and receiving infrared module. This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. Internal Audio Connectors (4-pin CD1) (CD1: see p. 11 No. 28) CD-L GND GND CD-R CD1 Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 11, No. 29) 1 GND PRESENCE# MIC_RET OUT_RET OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 25 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. For Windows® XP / XP 64-bit OS: Click “Audio I/O”, select “Connector Settings” , choose “Disable front panel jack detection”, and save the change by clicking “OK”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Click the right-top “Folder” icon , choose “Disable front panel jack detection”, and save the change by clicking “OK”. [. . . ] If you enable the option “Full Screen Logo” but you want to see the AddOn ROM information when the system boots, please select [Enabled]. The default value is [Enabled]. 55 Boot Logo Use this option to select logo in POST screen. This option only appears when you enable the option “Full Screen Logo”. Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature. [. . . ]