User manual ASROCK 939DUAL-SATA2

[. . . ] 939Dual-SATA2 User Manual Version 1. 1 Published July 2006 Copyright©2006 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). The current SATA SATA1 interface allows up to 1. 5 Gb/s data transfer rate. Serial ATA II Connector This Serial ATA II (SATA II) (SATA II_1: see p. 8 No. 10) connector supports SATA II data cables for internal storage SATA II_1 devices. The current SATA II interface allows up to 3. 0 Gb/s data transfer rate. It is recommended to plug SATAII HDD to SATAII connector (SATAII_1) and connect SATA HDD to SATA connector (SATA1 or SATA2). Serial ATA (SATA) Data Cable Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. 17 Serial ATA (SATA) Power Cable (Optional) connect to the SATA HDD power connector connect to the power supply Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. If those USB 2. 0 ports on the I/O panel are not sufficient, this USB 2. 0 header is available to support 2 additional USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. USB 2. 0 Header (9-pin USB67) (see p. 8 No. 21) 1 USB_PWR P-6 P+6 GND DUMMY GND P+7 P-7 USB_PWR USB 2. 0 Header (9-pin USB45) (see p. 8 No. 22) 1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY Infrared Module Header (5-pin IR1) (see p. 8 No. 25) 1 IRTX +5VSB DUMMY GND IRRX Internal Audio Connectors (4-pin CD1) (CD1: see p. 8 No. 36) CD-R GND GND CD-L CD1 Front Panel Audio Header (9-pin AUDIO1) (see p. 8 No. 27) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L DUMMY AUD-OUT-R MIC-POWER MIC 18 System Panel Header (9-pin PANEL1) (see p. 8 No. 17) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 8 No. 18) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 8 No. 19) GND +12V CHA_FAN_SPEED Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Please connect an ATX power supply to this connector. CPU Fan Connector (3-pin CPU_FAN1) (see p. 8 No. 3) GND +12V CPU_FAN_SPEED ATX Power Connector (20-pin ATXPWR1) (see p. 8 No. [. . . ] Parallel Port Mode Use this item to set the operation mode of the parallel port. If this option is set to [ECP+EPP], it will show the EPP version in the following item, "EPP Version". OnBoard Game Port Use this item to enable the Game Port or disable it. OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it. [. . . ]