User manual ASROCK A55M-HVS

[. . . ] A55M-HVS User Manual Version 1. 0 Published August 2011 Copyright©2011 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors (SATA_1: see p. 11, No. 9) These six Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. The current SATA2 interface allows up to 3. 0 Gb/s data transfer rate. SATA_3 SATA_5 Serial ATA (SATA) Data Cable (Optional) Print Port Header (25-pin LPT1) (see p. 11 No. 15) AFD# ERROR# PINIT# SLIN# SATA_1 SATA_2 SATA_4 SATA_6 Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on this motherboard. This is an interface for print port cable that allows convenient connection of printer devices. GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# USB 2. 0 Headers (9-pin USB6_7) (see p. 11 No. 23) 1 USB_PWR P-9 P+9 GND DUMMY Besides six default USB 2. 0 ports on the I/O panel, there are three USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. GND P+8 P-8 USB_PWR (9-pin USB10_11) (see p. 11 No. 24) 1 USB_PWR P-11 P+11 GND DUMMY GND P+10 P-10 USB_PWR 24 Infrared Module Header (5-pin IR1) (see p. 11 No. 20) 1 IRTX +5VSB DUMMY This header supports an optional wireless transmitting and receiving infrared module. GND IRRX Consumer Infrared Module Header (4-pin CIR1) (see p. 11 No. 25) GND PRESENCE# MIC_RET OUT_RET This header can be used to connect the remote controller receiver. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. 1 OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. You don’t need to connect them for AC’97 audio panel. System Panel Header (9-pin PANEL1) (see p. 11 No. 17) This header accommodates several system front panel functions. Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch. RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. 25 PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is off when the system is in S3/S4 sleep state or powered off (S5). HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. [. . . ] The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main Menu did not appear automatically, locate and double click on the file “ASSETUP. EXE” from the BIN folder in the Support CD to display the menus. 4. 2. 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects the installed devices. Please install the necessary drivers to activate the devices. 4. 2. 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports. Click on a specific item then follow the installation wizard to install it. 4. 2. 4 Contact Information If you need to contact ASRock or want to know more about ASRock, welcome to visit ASRock’s website at http://www. asrock. com; or you may contact your dealer for further information. 53 Installing OS on a HDD Larger Than 2TB in AHCI Mode This motherboard is adopting UEFI BIOS that allows Windows® OS to be installed on a large size HDD (>2TB). [. . . ]