User manual ASROCK AD2700-ITX

[. . . ] AD2700-ITX / AD2500-ITX User Manual Version 1. 0 Published November 2011 Copyright©2011 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Please refer to below procedures for the quick installation and usage of ASRock Smart Remote. Find the CIR header located next to the USB 2. 0 header on ASRock motherboard. USB 2. 0 header (9-pin, blue) CIR header (4-pin, white) Step2. Connect the front USB cable to the USB 2. 0 header (as below, pin 1-5) and the CIR header. Please make sure the wire assignments and the pin assignments are matched correctly. USB_PWR PP+ GND DUMMY 1 2 3 4 5 GND IRTX IRRX ATX+5VSB Step3. Install Multi-Angle CIR Receiver to the front USB port. If Multi-Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller, please try to install it to the other front USB port. 3 CIR sensors in different angles 1. When the CIR function is enabled, the other port will remain USB function. Please do not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market. * ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www. asrock. com 2. 3. 20 2. 7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins. 13) Setting Description 2-pin jumper Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds. 21 2. 8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors (SATAII_2: see p. 11 or 12, No. 16) These two Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA / SATA2 hard disk or the SATA2 connector on this motherboard. Either end of the 3. 5mm audio cable can be connected to the portable audio devices, such as MP3 player and mobile phone or the Line-in port of your PC. Besides the default USB 2. 0 ports on the I/O panel, there are two USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. Serial ATA (SATA) Data Cable (Optional) 3. 5mm Audio Cable (Optional) USB 2. 0 Headers (9-pin USB6_7) (see p. 11 or 12 No. 9) 1 USB_PWR P-9 P+9 GND DUMMY GND P+8 P-8 USB_PWR Consumer Infrared Module Header (4-pin CIR1) (see p. 11 or 12 No. [. . . ] If you have USB compatibility issue, it is recommended to select [Disabled] to enter OS. [UEFI Setup Only] - USB devices are allowed to use only under UEFI setup and Windows / Linux OS. Legacy USB 3. 0 Support Use this option to enable or disable legacy support for USB 3. 0 devices. The default value is [Disabled]. 39 3. 3. 7 Voltage Configuration DRAM Voltage Use this to select DRAM Voltage. [. . . ]