User manual ASROCK ALIVENF6G-DVI-3067 INSTALLATION GUIDE

[. . . ] No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Specifications and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. [. . . ] Besides, this motherboard provides independent display controllers for DVI-D and D-Sub ports to support dual VGA output so that DVI-D and D-sub ports can drive same or different display contents. To enjoy Dual Monitor feature, please refer to the below procedures for proper installation of DVI Graphics-SI card in advance. Connect the DVI-D connector of DVI-D input monitor to the DVI-D output connector of DVI Graphics-SI card which is inserted to PCIE1 (PCIE x16 slot) on this motherboard. If you have installed NVIDIA ® VGA driver from our support CD to your system already, you can freely enjoy the benefits of DVI-D output function with this motherboard after your system boots. If you haven't installed NVIDIA® VGA driver yet, please install NVIDIA® VGA driver from our support CD to your system and restart your computer. Then you can start to use DVI-D output function with this motherboard. Righ click the "NVIDIA Settings" icon on on the desktop to adjust the display mode you plan to use by following the instructions shown on the "NVIDIA Settings" screen. You are allowed to choose same or different display contents shown on the two monitors you install. Independent display controllers for DVI-D and D-Sub ports to support dual VGA output: DVI-D and D-sub ports can drive same or different display contents With the internal onboard VGA and the external add-on PCI Express VGA card, you can easily enjoy the benefits of Multi Monitor feature. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. These four Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. Please follow the instruction in our manual and chassis manual to install your system. If you use AC'97 audio panel, please install it to the front panel audio header as below: A. [. . . ] Then, please set the RAID configuration by using the Windows RAID installation guide in the following path in the Support CD: . If you want to install Windows® VistaTM or Windows® VistaTM 64-bit on your SATA / SATAII HDDs with RAID functions, please follow below steps. Before you start to configure RAID function, you need to check the RAID installation guide in the Support CD for proper configuration. Insert the Windows® VistaTM / Windows® VistaTM 64-bit optical disk into the optical drive to boot your system, and follow the instruction to install Windows® VistaTM / Windows® VistaTM 64-bit OS on your system. [. . . ]