User manual ASROCK CONROE865GV

[. . . ] ConRoe865GV User Manual Version 1. 0 Published August 2006 Copyright©2006 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 7) PIN1 IDE1 PIN1 IDE2 connect the black end connect the blue end to the IDE devices to the motherboard 80-conductor ATA 66/100 cable Note: If you use only one IDE device on this motherboard, please set the IDE device as "Master". Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). 11) SATA2 SATA1 These two Serial ATA (SATA) connectors support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. Serial ATA (SATA) Data Cable (Optional) 20 Serial ATA (SATA) Power Cable (Optional) connect to the SATA HDD power connector connect to the power supply Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. Besides six default USB 2. 0 ports on the I/O panel, there are two USB 2. 0 headers on this motherboard. The shared USB 2. 0 header (USB4_5) is shared with USB ports 45 on the I/O panel. When using the front panel USB ports by attaching the front panel USB cable to USB4_5 header, the USB ports 45 on the I/O panel will not be able to function. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. USB 2. 0 Header (9-pin USB67) (see p. 11 No. 18) 1 USB_PWR P-6 P+6 GND DUMMY GND P+7 P-7 USB_PWR Shared USB 2. 0 Header (9-pin USB4_5) (see p. 11 No. 28) USB_PWR P-4 P+4 GND 1 USB_PWR P-5 P+5 GND DUMMY Infrared Module Header (5-pin IR1) (see p. 11 No. 16) 1 IRTX +5VSB DUMMY GND IRRX Internal Audio Connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 11 No. 24) AUX-L GND GND AUX-R CD-L GND GND CD-R AUX1 CD1 Front Panel Audio Header (8-pin AUDIO1) (see p. 11 No. 22) 1 GND BACKOUT-R BACKOUT-L AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC 21 System Panel Header (9-pin PANEL1) (see p. 11 No. 14) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 11 No. 15) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 11 No. 13) GND +12V CHA_FAN_SPEED Please connect a chassis fan cable to this connector and match the black wire to the ground pin. You may connect either a 3-pin CPU Fan Connector (4-pin CPU_FAN1) (see p. 11 No. 5) 1 2 3 4 GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL or a 4-pin CPU fan cable to this connector, then match the black wire to the ground pin. Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. [. . . ] Tolerance ( C) The default value of tolerance is [2], which means the error of the target CPU temperature will be within 2 C. You can freely adjust the target fan speed according to the target CPU temperature that you choose. Configuration options: [Fast], [Middle] and [Slow]. 37 3. 5 Boot Screen In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. Main Advanced BIOS SETUP UTILITY H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Boot Device Priority Hard Disk Drives Removable Drives CD / DVD Drives Configure Settings during System Boot. Enter F1 F9 F10 ESC Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. 3. 5. 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Boot Settings Configuration Boot From Network Bootup Num-Lock [Disabled] [On] To enable or disable the boot from network feature. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. Boot From Network Use this item to enable or disable the Boot From Network feature. Boot Up Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up. 38 3. 5. 2 Boot Device Priority In this section, you may specify the boot sequence from the available devices in your system. BIOS SETUP UTILITY Boot Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [HDD: PM-MAXTOR 6L08] [CD / DVD] Specifies the boot sequence from the available devices. [. . . ]