User manual ASROCK H61TM-ITX

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ASROCK H61TM-ITX. We hope that this ASROCK H61TM-ITX user guide will be useful to you.


ASROCK H61TM-ITX : Download the complete user guide (4867 Ko)

Manual abstract: user guide ASROCK H61TM-ITX

Detailed instructions for use are in the User's Guide.

[. . . ] H61TM-ITX User Manual Version 1. 0 Published November 2012 Copyright©2012 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Adjust “Recording Volume”. Analog Surround Audio Header (17-pin HD_AUDIO2) (see p. 14, No. 27) PIN Signal Name 18 SENSE 16 LFE 14 A_GND 12 Surr_Rear_R 10 A_GND 8 Surr_Side_R 6 A_GND 4 Front_R 2 A_GND PIN Signal Name 17 KEY 15 A_GND 13 Center 11 A_GND 9 Surr_Rear_L 7 A_GND 5 Surr_Side_L 3 A_GND 1 Front_L 27 3W Audio AMP Output Wafer Header (4-pin SPEAKER1) (see p. 14, No. 28) Please connect the chassis speaker to this header. Power LED Header (3-pin PLED1) (see p. 14, No. 11) Please connect the chassis power LED to this header to indicate system power status. The LED is off in S4 state or S5 state (power off). Chassis Fan Connector (4-pin CHA_FAN1) (see p. 14, No. 4) Please connect a fan cable to the fan connector and match the black wire to the ground pin. CPU Fan Connectors (4-pin CPU_FAN1) (see p. 14, No. 22) Though this motherboard provides a 4-Pin CPU fan (Quiet Fan) connector, 3-Pin CPU fans can still work even without fan speed control. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. Serial Port Header (10-pin COM1) (see p. 14, No. 18) RI RTS GND TXD DCD 1 NC CTS DSR DTR RXD This COM1 header supports a serial port module. 28 HDMI_SPDIF Header (2-pin HDMI_SPDIF1) (see p. 14, No. 25) This header provides SPDIF audio output to HDMI VGA cards, allowing the system to connect HDMI Digital TV/projector/LCD devices. Please connect the HDMI_ SPDIF connector of a HDMI VGA card to this header. Backlight & Amp Volume Control Header (8-pin BLT_VOL1) (see p. 14, No. 17) 1 1: BKLT_EN 2: BKLT_PWM 3: BKLT_PWR 4: BKLT_PWR 5: GND 6: GND 7: Brightness_Up 8: Brightness_Down Digital MIC Header (5-pin DMIC1) (see p. 14, No. 24) 1: +5V 2: No pin 2: SPDIF_OUT/DMIC_CLK 3: GND 4: DMIC_DATA 5: +3. 3V Home Theater PC Header (7-pin HTPC1) (see p. 14, No. 29) PIN Signal Name PIN Signal Name 8 HDMI CEC 7 #Power_Button 6 SMB_DATA 5 3. 3V Standby 4 SMB_CLK 3 No pin 2 GND 1 Recording LED 29 LPC Debug Header (13-pin LPC1) (see p. 14, No. 30) PIN Signal Name 14 +3V 12 +3V 10 GND 8 LAD3 6 LAD1 4 LFRAME# 2 GND PIN Signal Name 13 No pin 11 +3V 9 GND 7 LAD2 5 LAD0 3 RESET# 1 CLK LVDS Panel Connector (40-pin LVDS1) (see p. 14, No. 15) PIN 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Signal Name LCD_VCC LCD_VCC LCD_VCC EDID_GND EVEN_Lane0_N EVEN_Lane0_P EVEN_Lane1_N EVEN_Lane1_P EVEN_Lane2_N EVEN_Lane2_P EVEN_Lane3_N EVEN_Lane3_P ODD_Lane0_N ODD_Lane0_P ODD_Lane1_N ODD_Lane1_P ODD_Lane2_N ODD_Lane2_P ODD_Lane3_N ODD_Lane3_P PIN Signal Name 40 EDID_DATA 39 NC 38 BKLT_PWR 37 BKLT_PWR 36 BKLT_PWR 35 EVEN_CLK_N 34 EVEN_CLK_P 33 BKLT_PWM_DIM 32 BKLT_ENABLE 31 EDID_CLK 30 BKLT_GND 29 BKLT_GND 28 BKLT_GND 27 ODD_CLK_N 26 ODD_CLK_P 25 LCD_GND 24 LCD_GND 23 LCD_GND 22 EDID_3. 3V 21 NC 30 2. 9 Jumpers Setup When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRCMOS1) (see p. 14, No. 31) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. [. . . ] Please be noted that the USB flash drive or hard drive must use FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the UEFI files and their respective information. Select the proper UEFI file to update your UEFI, and reboot your system after the UEFI update process is completed. Internet Flash Internet Flash searches for available UEFI firmware updates from our servers. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ASROCK H61TM-ITX




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ASROCK H61TM-ITX will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.