User manual ASROCK IMB-147 SERIES

[. . . ] IMB-147 User Manual Version 1. 0 Published January 2013 Copyright©2013 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Though this motherboard provides a 4-Pin CPU fan (Quiet Fan) connector, 3-Pin CPU fans can still work successfully even without fan speed control. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. CPU Fan Connector (4-pin CPU_FAN1) (see p. 10, No. 5) GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL 18 Serial Port Header (10-pin COM4) (see p. 10, No. 21) PIN 1 2 3 4 5 2 PIN Signal Name PIN Signal Name 2 4 6 8 10 NC CTS DSR DTR RXD 1 3 5 7 9 COM VOLT RTS GND TXD DCD 1 RS232 DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND RS422 TX+ RXTXRX+ GND RS485 RTX+ N/A RTXN/A GND LVDS Connector (40-pin LVDS1) (see p. 10, No. 2) 39 40 PIN 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 Signal Name GND LVDS2 D3(-) LVDS2 CLK(-) LVDS2 D2(-) LVDS2 D1(-) LVDS2 D0(-) GND LVDS1 D3(-) LVDS1 CLK(-) LVDS1 D2(-) LVDS1 D1(-) LVDS1 D0(-) B/L ENABLE B/L ADJUST DDC CLK LVDS PWR VCC 3. 3V +12V +12V +12V PIN 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 Signal Name GND LVDS2 D3(+) LVDS2 CLK(+) LVDS2 D2(+) LVDS2 D1(+) LVDS2 D0(+) GND LVDS1 D3(+) LVDS1 CLK(+) LVDS1 D2(+) LVDS1 D1(+) LVDS1 D0(+) GND LVDS PWR EN DDC DATA LVDS PWR GND GND +12V +12V 1 2 19 Inverter Power Control Connector (5-pin BLT_PWR3) (see p. 10, No. 4) PIN 1 Signal Name +12V GND B/L ENABLE B/L ADJUST +5V 1 2 3 4 5 Backlight & Amp Volume Control Header (7-pin BLT_VOL1) (see p. 10, No. 1) PIN 1 Signal Name VOL_UP VOL_DW BKT_OFF BKT_UP BKT_DW GND GND 1 2 3 4 5 6 7 GPIO&AMP Header (10-pin DGIO_AMP1) (see p. 10, No. 22) 2 PIN Signal Name 2 4 6 8 10 SMB_DATA GPO[1] GPO[0] AMP R(-) AMP R(+) PIN Signal Name 1 3 5 7 9 SMB_CLK GPI[1] GPI[0] AMP L(-) AMP L(+) 1 Internal Speaker Header (4-pin SPEAKER1) (see p. 10, No. 27) 1 SPK_RSPK_R+ SPK_LSPK_L+ 20 VGA Header (10-pin VGA_H1) (see p. 10, No. 28) 1 2 PIN Signal Name PIN Signal Name 9 7 5 3 1 RED GRN BLUE HSYNC DDC_CLK 10 8 6 4 2 GND GND GND VSYNC DDC_DAT 21 2. 7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. 18) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. COM Port Power Setting Jumpers (3-pin COM4) (see p. 10, No. 17) 1-2 : +5V 2-3 : +12V 22 Panel Power Jumper (3-pin PNL_PWR1) (see p. 10, No. 3) 1-2 : +3V 2-3 : +5V ATX/AT Mode Jumper (3-pin PWR_JP1) (see p. 10, No. 13) 1-2 : AT Mode 2-3 : ATX Mode 23 2. 8 Operating System Setup This motherboard supports Microsoft® Windows® 7. [. . . ] Onboard LAN2 This allows you to enable or disable the Onboard LAN2. 35 3. 3. 3 Storage Configuration Onboard SATAII Mode Use this to select the SATA mode for SATA2_1 and SATA2_2 ports. (Self-Monitoring, Analysis, and Reporting Technology). 36 3. 3. 4 Super IO Configuration COM1 Port Use this to enable or disable COM1 port. COM6 Port Address Use this to set the address for COM1 port. 37 LPT1 Port Use this to enable or disable LPT1 port. WDT Timeout Reset This allows users to enable or disable the Watch Dog Timer timeout to reset the system. 38 3. 3. 5 ACPI Configuration Suspend to RAM Use this to select whether to auto-detect or disable Suspend-toRAM. [. . . ]