User manual ASROCK K7UPGRADE-880

[. . . ] K7Upgrade-880 User Manual Version 1. 0 Published August 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 25) 1 USB_PWR P-7 P+7 GND DUMMY GND P+6 P-6 USB_PWR Shared USB 2. 0 Header (9-pin USB45) (see p. 8, No. 41) USB_PWR P-4 P+4 GND 1 USB_PWR P-5 P+5 GND DUMMY Infrared Module Header (5-pin IR1) (see p. 8, No. 28) 1 IRTX +5V DUMMY GND IRRX Internal Audio Connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 8, No. 39) CD-R GND GND CD-L AUX-R GND GND AUX-L CD1 AUX1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. Front Panel Audio Header (9-pin AUDIO1) (see p. 8, No. 35) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC 19 System Panel Header (9-pin PANEL1) (see p. 8, No. 22) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 8, No. 24) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 8, No. 21) GND +12V CHA_FAN_SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Connect a Game cable to this connector if the Game port bracket is installed. CPU Fan Connector (3-pin CPU_FAN1) (see p. 8, No. 2) CPU_FAN_SPEED +12V GND Game Connector (15-pin GAME1) (see p. 8, No. 29) +5V JAB2 JAY GND GND JAX JAB1 +5V 1 +5V JBB1 JBX MIDI_OUT J2Y JBY MIDI_IN ATX Power Connector (20-pin ATXPWR1) (see p. 8, No. 38) Please connect an ATX power supply to this connector. 20 ATX 12V Connector (4-pin ATX12V1) (see p. 8, No. 6) Please note that it is necessary to connect a power supply with ATX 12V plug to this connector so that it can provides sufficient power. Failing to do so will cause the failure to power up. 1 PLEDPLED+ PLED+ Power LED Header (3-pin PWR_LED1) (see p. 8 No. 23) Please connect a 3-pin power LED cable to this header. AT (SAT 2. 7 Serial ATA (SATA) Hard Disks Installation This motherboard supports Serial ATA (SATA) hard disks and RAID functions. You may install SATA hard disks on this motherboard for internal storage devices. STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 3: Connect one end of the SATA data cable to the motherboard's SATA connector. STEP 4: Connect the other end of the SATA data cable to the SATA hard disk. Functions SAT 2. 8 Hot Plug and Hot Swap Functions for SATA HDDs K7Upgrade-880 motherboard supports Hot Plug and Hot Swap functions for SATA Devices. What is Hot Plug Function? If the SATA HDDs are NOT set for RAID configuration, it is called "Hot Plug" for the action to insert and remove the SATA HDDs while the system is still power-on and in working condition. [. . . ] Parallel Port Address Use this item to set the address for the onboard parallel port or disable it. Parallel Port Mode Use this item to set the operation mode of the parallel port. If this option is set to [ECP+EPP], it will show the EPP version in the following item, "EPP Version". Configuration options: [IRQ5] and [IRQ7]. 36 OnBoard Game Port Use this item to enable the Game Port or disable it. [. . . ]