User manual ASROCK K7VT4A

[. . . ] K7VT4A User Manual Version 1. 0 Published November 2003 Copyright©2003 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). USB 2. 0 Connector (9-pin USB45) (see p. 7 item 17) 1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY ASRock I/OTM provides you 4 default USB 2. 0 ports on the rear panel. If the rear USB ports are not sufficient, this USB 2. 0 connector is available to support 2 additional USB 2. 0 ports. This connector supports an optional wireless transmitting and receiving infrared module. Infrared Module Connector (5-pin IR1) (see p. 7 item 18) 1 IRTX +5V DUMMY GND IRRX 15 Internal Audio Connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 7 item 28) (AUX1: see p. 7 item 27) AUX-L GND GND AUX-R AUX1 These connectors allow you to receive stereo audio input from sound sources such as a CDROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. CD-L GND GND CD-R CD1 Front Panel Audio Connector (9-pin AUDIO1) (see p. 7 item 24) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L DUMMY AUD-OUT-R MIC-POWER MIC System Panel Connector (9-pin PANEL1) (see p. 7 item 15) 1 PLED+ PLEDPWRBTN# GND This connector accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Connector (4-pin SPEAKER 1) (see p. 7 item 16) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this connector. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 7 item 12) GND +12V CHA_FAN_SPEED Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect a CPU fan cable to this connector and match the black wire to the ground pin. Please connect an ATX power supply to this connector. CPU Fan Connector (3-pin CPU_FAN1) (see p. 7 item 2) CPU_FAN_SPEED +12V GND ATX Power Connector (20-pin ATXPWR1) (see p. 7 item 6) Power LED Connector (3-pin PWR_LED1) (see p. 7 item 14) 1 PLEDPLED+ PLED+ Please connect a 3-pin power LED cable to this connector. 16 Chapter 3 BIOS Setup 3. 1 BIOS Setup Utility This section explains how to use the BIOS Setup Utility to configure your system. Please press <F2> during the PowerOn-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST will continue with its test routines. If you wish to enter the BIOS Setup after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart the system by turning the system off and then back on. It is a menu-driven program, which allows you to scroll through its various sub-menus and select among the predetermined choices. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and may not exactly match what you see on your screen. 3. 1. 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Sets up the basic system configuration ADVANCED Sets up the advanced features SECURITY Sets up the security features POWER Configures Power Management features BOOT Configures the default system device that is used to locate and load the Operating System EXIT Exits the current menu or the BIOS Setup To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted. 3. 1. 2 Legend Bar At the bottom of the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions. 17 Navigation Key(s) <F1> <ESC> / / +/<Enter> <F9> <F10> Function Description Displays the General Help Screen Jumps to the Exit menu or returns to the upper menu from the current menu Moves cursor up or down between fields Selects menu to the left or right Increases or decreases values Brings up a selected menu for a highlighted field Loads all the setup items to default value Saves changes and exits Setup 3. 2 Main Menu When you enter the BIOS Setup Utility, the following screen appears. AMIBIOS SETUP UTILITY - VERSION 3. 31a Boot Power Exit Main Advanced Security [ System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed L1 Cache Size L2 Cache Size Total Memory DDR1 DDR2 Setup Help ] Oct 31 2003 Fri 20:07:40 Month: Jan - Dec Day: 01 - 31 Year: 1980 - 2099 K7VT4A BIOS P1. 00 AMD Athlon(tm) XP 2600+ 2133 MHz 128 KB 256 KB 512 MB 512 MB / 200 MHz (DDR400) None F1:Help Esc:Exit :Select Item :Select Menu +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit System Date [Month/Day/Year] Set the system date that you specify. Valid values for month, day, and year are Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). System Time [Hour:Minute:Second] Set the system to the time that you specify. IDE Devices Use this to configure IDE devices. 18 TYPE To set the type of the IDE device, first, please select "IDE Devices" on Main menu and press <Enter> to get into the sub-menu. Then, select among "Primary IDE Master", "Primary IDE Slave", "Secondary IDE Master", and "Secondary IDE Slave" to make configuration of its type. Below are the configuration options. AMIBIOS SETUP UTILITY - VERSION 3. 31a Main Primary IDE Master [ Setup Help ] Auto Select how to set the parameters of drive, Or Select [AUTO] to set all HDD parameters automatically. Off Off Auto Off Auto Type Cylinders Heads Write Precompensation Sectors Maximum Capacity LBA Mode Block Mode Fast Programmed I/O Modes 32 Bit Transfer Mode Ultra DMA Mode F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit [USER]: It allows user to manually enter the number of cylinders, heads, and sectors per track for the drive. Before attempting to configure a hard disk drive, make sure you have the correct configuration information supplied by the drive manufacturer. Incorrect settings may cause the system to fail to recognize the installed hard disk. [. . . ] If [Always] option is selected, the "Password Check" is performed before both boot-up and BIOS setup. 26 3. Power Setup Menu Main Advanced Security AMIBIOS SETUP UTILITY - VERSION 3. 31a Boot Power Exit [ Setup Help ] Suspend To RAM Repost Video on STR Resume Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second Disabled Disabled Power Off Disabled Disabled Disabled Disabled Every Day 12 30 30 <Enter> to select auto-detect or disable the Suspend-to-RAM feature. F1:Help Esc:Exit :Select Item :Select Menu +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit Suspend to RAM: This field allows you to select whether to auto-detect or disable the Suspend-to-RAM feature. Repost Video on STR Resume: This feature allows you to repost video on STR resume. It is recommended to enable this feature under Microsoft® Windows® 98 / ME. [. . . ]