User manual ASROCK K8VM890

[. . . ] K8VM890 User Manual Version 1. 1 Published February 2006 Copyright©2006 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] If the rear USB ports are not sufficient, this USB 2. 0 header is available to support 2 extra USB 2. 0 ports. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. GND IRRX Internal Audio Connectors (4-pin CD1) (CD1: see p. 9, No. 27) CD-R GND GND CD-L CD1 Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 9, No. 25) 1 GND PRESENCE# MIC_RET OUT_RET OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC'97 audio panel, please install it to the front panel audio header as below: A. Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager. Click "Audio I/O", select "Connector Settings" , choose "Disable front panel jack detection", and save the change by clicking "OK". 17 System Panel Header (9-pin PANEL1) (see p. 9, No. 17) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 9, No. 18) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 9, No. 16) GND +12V CHA_FAN_SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Connect a Game cable to this connector if the Game port bracket is installed. CPU Fan Connector (3-pin CPU_FAN1) (see p. 9, No. 6) CPU_FAN_SPEED +12V GND Game Connector (15-pin GAME1) (see p. 9, No. 21) 1 +5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN +5V JAB2 JAY GND GND JAX JAB1 +5V ATX Power Connector (20-pin ATXPWR1) (see p. 9, No. 9) Please connect an ATX power supply to this connector. ATX 12V Connector (4-pin ATX12V1) (see p. 9, No. 2) Please note that it is necessary to connect a power supply with ATX 12V plug to this connector so that it can provides sufficient power. Failing to do so will cause the failure to power up. 18 COM Port Header (9-pin COM1) (see p. 9 No. 30) 1 RRXD1 DDTR#1 DDSR#1 CCTS#1 This COM port header is used to support a COM port module. RRI#1 RRTS#1 GND TTXD1 DDCD#1 AT (SAT 2. 8 Serial ATA (SATA) Hard Disks Installation This motherboard supports Serial ATA (SATA) hard disks and RAID functions (RAID0, 1, JBOD). STEP 1: Install the SATA hard disks into the drive bays of your chassis. [. . . ] If this option is set to [ECP+EPP], it will show the EPP version in the following item, "EPP Version". Configuration options: [IRQ5] and [IRQ7]. 33 OnBoard Game Port Use this item to enable the Game Port or disable it. OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330]. 3. 3. 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration USB Controller USB 2. 0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] To enable or disable the onboard USB controllers. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. USB Controller Use this item to enable or disable the use of USB controller. [. . . ]