User manual ASROCK M266A

[. . . ] M266A User Manual Version 1. 0 Published April 2003 Copyright©2003 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Jumper PS2_USB_PWR1 (see p. 7 item 22) Short Open Setting 1_2 2_3 Description Short pin2, pin3 to enable +5VSB (standby) for PS/2 or USB wake up events. Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply. +5V +5VSB Clear CMOS CLRCMOS1 (see p. 7 item 17) solder points Note: These solder points allow you to clear the data in the CMOS. The data in the CMOS includes system setup information such as the system password, date, time, and the system setup parameters. To clear and reset the system parameters to the default setup, please turn off the computer and unplug the power cord, then short the solder points for more than 3 seconds by using metal material, e. g. , a paper clip. Please remember to remove the paper clip after clearing the CMOS. 13 2. 7 Connectors Connectors are NOT jumpers. Connector FDD connector (33-pin FLOPPY1) (see p. 7 item 10) Pin1 FLOPPY1 Red marking Figure Description Note: Match the red marking on the floppy ribbon cable with Pin1 Primary IDE connector (Blue) (39-pin IDE1, see p. 7 item 7) Secondary IDE connector (Black) (39-pin IDE2, see p. 7 item 8) PIN1 IDE1 PIN1 IDE2 connect the black end to the IDE devices connect the blue end to the motherboard 80-Pin ATA 100/133 cable Note: To optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). USB 2. 0 header (9-pin USB45) (see p. 7 item 13) ASRock I/OTM provides you 4 default USB 2. 0 ports on the rear panel. If the rear USB ports are not sufficient, this USB 2. 0 header is available for 2 additional USB 2. 0 ports. This connector supports an optional wireless transmitting and receiving infrared module. Infrared module connector (5-pin IR1) (see p. 7 item 14) 14 Internal audio connectors (4-pin CD1, 4-pin AUX1) (CD1: see p. 7 item 24) (AUX1: see p. 7 item 23) AUX1 CD1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices. Front panel audio connector (9-pin AUDIO1) (see p. 7 item 20) System panel connector (9-pin PANEL1) (see p. 7 item 12) This connector accommodates several system front panel functions. External speaker connector (4-pin SPEAKER 1) (see p. 7 item 15) This connector allows you to attach to an external speaker. Connect the fan cable to the connector matching the black wire to the ground pin. Connect the fan cable to the connector matching the black wire to the ground pin. Connect an ATX power supply to the connector. Chassis fan connector (3-pin CHA_FAN1) (see p. 7 item 9) CPU fan connector (3-pin CPU_FAN1) (see p. 7 item 3) ATX power connector (20-pin ATXPWR1) (see p. 7 item 1) Serial port connector (9-pin COM1) (see p. 7 item 25) This connector supports a serial port module. 15 Chapter 3 BIOS Setup 3. 1 BIOS Setup Utility This section explains how to configure your system using the BIOS Setup Utility. When you start up the computer, there is a chance for you to run the BIOS Setup. Press <F2> during the Power-On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST continues with its test routines. If you wish to enter the BIOS Setup after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for refer ence purpose only, and may not exactly match what you see on your screen. 3. 2 BIOS Setup Utility Main Menu When you enter the BIOS Setup utility, the following screen appears: AMIBIOS SETUP UTILITY - VERSION 3. 31a M266A BIOS P1. 0 Standard CMOS Setup Advanced CMOS Setup Advanced Chipset Setup Power Management Setup PCI / Plug and Play Setup Peripheral Setup Hardware Monitor Setup Change Supervisor Password Change User Password Auto Configuration with Optimal Settings Save Savings and Exit Exit Without Saving F1: Help Esc: Exit : Select Item : Select Menu +/-: Change Values Enter: Select Sub-Menu F9: Setup Defaults F10: Save & Exit Set Time, Date, Hard Disk Type . . The main menu of the Setup Utility displays a list of the options that are available. Use arrow keys to move the highlight bar to select items, then press <Enter> to make configuration for a specific item. 16 3. 3 Legend Bar At the bottom of all the Setup Screen is a legend bar. The following table lists the keys in the legend bar with their corresponding functions: Navigation Key(s) <F1> <ESC> / / +/<Enter> <F9> <F10> Function Description Displays the General Help Screen Jumps to the Exit menu or returns to the upper menu from the current menu Moves cursor up or down between fields Selects menu to the left or right Increases or decreases values Brings up a selected menu for a highlighted field Loads all the setup items to the default value Saves changes and exits Setup 3. 4 Standard CMOS Setup This menu lists out the basic information about your system. AMIBIOS SETUP UTILITY - VERSION 3. 31a Standard CMOS Setup System Date System Time Floppy Drives IDE Devices BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DDR1 DDR2 SDR1 SDR2 [ Setup Help ] Apr 10 2003 Thu 20:07:40 Month: Jan - Dec Day: 01 - 31 Year: 1980 - 2099 M266A BIOS P1. 00 Pentium (R) 4 Family CPU 2400 MHz 512 KB F24 / 0F 224 MB + 32 MB Share Memory 256 MB / 266 MHz None None None F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit System Date [Month/Day/Year] Set the system date that you specify. Valid values for month, day, and year are Month: [Jan to Dec], Day: [1 to 31], Year: [1980 to 2099). System Time [Hour:Minute:Second] Set the system to the time that you specify. [. . . ] RTC Alarm Power On Use this to enable or disable RTC (Real Time Clock) to power on the system. If [Enable] is selected, you must fill the RTC Alarm Date / Hour / Minute / Second sub-fields with the actual wake up time you desire. 23 3. 8 PCI / Plug and Play Setup AMIBIOS SETUP UTILITY - VERSION 3. 31a PCI / Plug and Play Setup PCI Latency Timer (PCI Clocks) Primary Graphics Adapter [ 32 PCI Setup Help ] <Enter> to select PCI clocks. Leave on default setting for the best PCI performance. F1:Help Esc:Previous Menu :Select Item +/-:Change Values Enter:Select Sub-Menu F9:Setup Defaults F10:Save & Exit PCI Latency Timer (PCI Clocks) The default is 32. We recommend you to keep the default value unless your PCI expansion cards' specifications require other settings. [. . . ]