User manual ASROCK P4V88 PLUS

[. . . ] You may find the latest memory and CPU support lists on ASRock website as well. 8 cm Socket 478, supports Intel® Pentium® 4 (Prescott, Northwood, Willimate) / Celeron® processor Chipsets: North Bridge: VIA PT880, FSB @ 800/533/400 MHz, with Intel® Hyper-Threading Technology ready (see CAUTION 1) South Bridge: VIA VT8237, supports USB 2. 5GB, Dual Channel Memory Technology support (see CAUTION 2) IDE: IDE1: ATA 133 / Ultra DMA Mode 6 IDE2: ATA 133 / Ultra DMA Mode 6 Support up to 4 IDE devices Serial ATA: 2 SATA connectors, support up to 1. 3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor: CPU temperature sensing, Chassis temperature sensing, CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 3), CPU fan tachometer, Chassis fan tachometer, Voltage monitoring: +12V, +5V, +3V, Vcore PCI slots: 5 slots with PCI Specification 2. [. . . ] Please make sure to disconnect power supply before adding or removing DIMMs or the system components. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface. The ASRock AGP slot has a special design of clasp that can securely fasten the inserted graphics card. For the voltage information of your AGP card, please check with the AGP card vendors. STEP 1: Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. STEP 3: Align the card connector with the slot and press firmly until the card is completely seated on the slot. The illustration shows a 3-pin jumper whose pin1 and pin2 are "Short" when jumper cap is placed on these 2 pins. Short pin2, pin3 to enable +5VSB (standby) for PS/2 or USB wake up events. Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply. 25) Note: If the JL1 and JR1 jumpers are short, both the front panel and the rear panel audio connectors can work. the data in CMOS includes system setup information such as system password , date , time , and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Note: If you use only one IDE device on this motherboard, please set the IDE device as "Master". please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). These two Serial ATA (SATA) connectors support SATA data cables for internal storage devices. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard. [. . . ] Please refer to the document in the Support CD, "Guide to SATA Hard Disks Installation and RAID Configuration", which is located in the folder at the following path: . \ SATA RAID BIOS STEP 3: Install Windows 2000 / Windows XP OS on your system. After making a SATA driver diskette and using "SATA RAID BIOS" to set RAID configuration, you can start to install Windows 2000 / Windows XP on your system. After the installation of Windows 2000 / Windows XP OS, if you want to manage RAID functions, you are allowed to use both "SATA RAID BIOS" and "VIA RAID Tool" for RAID configuration. [. . . ]