User manual ASROCK P67 EXTREME4

[. . . ] P67 Extreme4 User Manual Version 1. 0 Published September 2010 Copyright©2010 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identi cation or explanation and to the owners' bene t, without intent to infringe. Disclaimer: Speci cations and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Each USB 2. 0 header can support two USB 2. 0 ports. (9-pin USB10_11) (see p. 12 No. 29) 1 USB_PWR P-11 P+11 GND DUMMY GND P+10 P-10 USB_PWR (9-pin USB12_13) (see p. 12 No. 28) 1 USB_PWR P-13 P+13 GND DUMMY GND P+12 P-12 USB_PWR USB 3. 0 Header (19-pin USB3_2_3) (see p. 12 No. 26) IntA_P2_D+ IntA_P2_DGND IntA_P2_SSTX+ IntA_P2_SSTXGND IntA_P2_SSRX+ IntA_P2_SSRXVbus Besides two default USB 3. 0 ports on the I/O panel, there is one USB 3. 0 header on this motherboard. This USB 3. 0 header can support two USB 3. 0 ports. 1 Vbus IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ ID Infrared Module Header (5-pin IR1) (see p. 12 No. 32) 1 IRTX +5VSB DUMMY This header supports an optional wireless transmitting and receiving infrared module. GND IRRX Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 12 No. 35) 1 GND PRESENCE# MIC_RET OUT_RET This is an interface for front panel audio cable that allows convenient connection and control of audio devices. OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 34 1. High De nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC'97 audio panel, please install it to the front panel audio header as below: A. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust "Recording Volume". System Panel Header (9-pin PANEL1) (see p. 12 No. 24) This header accommodates several system front panel functions. Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may con gure the way to turn off your system using the power switch. RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is off when the system is in S3/S4 sleep state or powered off (S5). HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. 35 The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. [. . . ] Bootup Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up. The default value is [Enabled]. 71 AddOn ROM Display Use this option to adjust AddOn ROM Display. If you enable the option "Full Screen Logo" but you want to see the AddOn ROM information when the system boots, please select [Enabled]. Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature. [. . . ]