User manual AT&T 8220

[. . . ] If you need a replacement, call 1 800 222­3111. 3 4 Charge the handset battery. After the first charge, the battery is typically fully charged overnight. After the batteries are charged, pick up the handset and press P; you should hear a dial tone. 5 Set the dial mode. If you have touch tone service, the phone is ready to use as soon as the batteries are charged. [. . . ] The telephone might operate before that, but for best performance, let the battery pack charge fully. 2 3 4 5 3 TELEPHONE OPERATION Answer a Call Lift handset from base -- OR -- Press any key. Headset Jack You can use this telephone hands-free when you install a 2. 5 mm headset, included or purchased separately. Do not force the connection, but make sure the plug fits securely. Make a Call Press and wait for light to go on steadily. End a Call Place handset in base -- OR -- Press O. Cancel a page. Flash/Call Waiting Access special telephone company subscriber services. Redial Temporary Tone Dialing Press to change from dial pulse to touch tone dialing during a call. This is useful if you have dial pulse (rotary) service and need to send touch tone signals for access to telephone banking or long-distance services. 3 After you hang up, the phone automatically returns to dial pulse (rotary) service. Press P, then press to call the last number dialed (up to 16 digits). Change Channel Press to switch to a clearer channel. Handset Ringer Style/ Battery Save Select from four different handset ringer styles, or turn the ringer off and extend battery life. 3 Press 1, 2, 3 or 4 to select your ringer style (you will hear a sample), or press 5 to turn the ringer off. When the ringer is off, select a ringer style to turn it on again. Handset Volume Adjust volume of what you hear through the handset. 4 TELEPHONE OPERATION Page/Handset Locator Press once to page the handset for up to one minute -- OR -- Press twice to cancel. Indicates handset is charging in base Indicates handset is in use 5 TELEPHONE MEMORY This cordless phone can store 10 telephone numbers, each up to 16 digits long. You can dial numbers stored in memory just by pressing P, M and a number button. Store Memory Numbers 1 Make sure the handset is off. 3 Press the number button (0­9) where you want to store the telephone number. 4 Dial the telephone number (up to 16 digits) -- OR -- Press to store the last number dialed. 5 Press M. Store a Pause in a Memory Number Press to store a two-second pause in the dialing sequence. Each press adds another two-second pause and counts as one digit. Change/Replace a Stored Memory Number Store a new number in its place. Directory Label Dial Memory Numbers 1 Press P. 2 Press and release M, then press the number button (0­9) where the memory number is stored. Use the included self-adhesive directory label to keep a record of the numbers (or names) stored in memory. It's best to write on the label before applying it to the phone. 6 IN C ASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at www. telephones. att. com or call 1 800 222­3111. Please retain your receipt as your proof of purchase. If you hear noise or interference when using the phone: · · · Make sure the base antenna is fully upright. [. . . ] If the handset does not beep when you press P, the battery might need charging. If you have dial pulse (rotary) service on your phone line, make sure the dial mode is set to dial pulse (see INSTALLATION). · · · If you hear other calls while using your phone: · · If the above suggestions don't solve the problem, try re-initializing the handset and base: 1 2 3 4 5 6 Disconnect the power to the base. Put the handset in the base to re-initialize. If you lose a call after changing channels: You were probably almost out of range. Before placing another call, set the handset in the base for at least 15 seconds. If you are unable to operate special telephone services or other equipment requiring touch tone signals: If you have dial pulse (rotary) service, follow the directions under "Temporary Tone Dialing" in the TELEPHONE OPERATION section of this manual. If you hear a two-beep signal when you try to use the handset: · · · You might be out of range. [. . . ]