User manual AUDIOVOX AOS58

[. . . ] The Voyager observation System is not intended to in any way be a substitute for careful, cautious, defensive driving or for the consistent adherence to all applicable traffic laws and motor safety regulations. This product is not intended to be a substitute for rear view mirrors, or for any other motor vehicle, or boat equipment mandated by law. FEATURES: AOC-75 CCD Camera - 270, 000 pixel image sensor - 0. 1 Lux sensitivity - Automatic electronic iris provides a clearer, more consistent image in low and bright light - Wide angle lens provides a broad viewing area - Compact design and light weight simplify installation in most vehicles, including large boats - Durable, waterproof construction - Built-in Microphone for audio pick-up - Normal /Mirror switch on back of camera - Wind Deflector reduces build up of dirt on lens - Waterproof cable connector AOM-58 Monochrome 5" Monitor - Day/Night switch - Brightness and contrast controls - Volume control - Illuminated front panel - Internal speaker with external speaker jack Contents of one Complete Package: AOC-75 Camera Qty. [. . . ] Do not use strong cleaning agents containing gasoline, benzene, or alcohol. This reduces the possibility of being hooked during operation of the vehicle. Keep all cables away from HOT, ROTATING and ELECTRICALLY NOISY components. 4. To increase protection of cable, place all excess wire and extension cable in convoluted tubing. See wiring diagram for connections to ignition, ground, and backup circuit. Wiring camera: Drill a 19mm /3/4" diameter hole into the vehicle body near the camera and bracket. 3 Push extra cable into vehicle, (be careful not to kink cable) and fit grommet into the hole. Apply sealant around grommet to increase resistance to water penetration. Wiring monitor: Insert extension cable into the camera #1 position if (2) cameras are used, be sure to mark each extension cable properly and plug second camera into cable #2 position. The red wire marked ACC is connected to an ignition power source, the black wire marked GND is connected to chassis ground, and the blue wire marked BACK is connected to the vehicle's back up circuit. BY- Monitor operates when vehicle transmission is switched into "reverse". On- Monitor and system operate when ignition switch is "ON" 2. Input Switch: "A" used mainly for rear mounted camera or as specified by the installer. "B" used mainly for side mounted camera or as specified by the installer. Day/Night Switch: Pre-set brightness and contrast levels optimized for day and night operation. Should be adjusted if the "Day/Night" switch does not achieve the most desirable 5. [. . . ] Holes 1. 401 2. 601 Camera Mounting Hole Pattern Figure 1 6 1. 010 . 534 80° Approximately 80° Field of View Back of Vehicle, View at Monitor Screen Figure 2 7 Included Wind Deflector- Optional Installation Screw for use w/Wind deflector #8-32 x 3/8" 4mm x . 7mm x 25. 4mm Phillips Hex Head Screw w/Washers 4mm x . 7mm Hex Nuts Screw for use Without Wind Deflector #8-32 x 5/16" 4mm x . 7mm x 25. 4mm Phillips Hex Head Screw w/Washers 4mm x . 7mm Hex Nuts Figure 3 8 Plain Washer Spring Washer Dashboard or Overhead Steel Plate Reinforcement (Recommended for Secure Mounting) Figure 4 9 20° 20° 5-0. 236 Dia. Holes 2. 250 5. 275 6. 240 110. 0° Monitor Mounting Hole Pattern Figure 5 10 2. 677 WIND DEFLECTOR- OPTIONAL INSTALLATION EMI FERRITE CORE WATERPROOF CAMERA CONNECTION 20 METERS TO MONITOR CAMERA "A" INPUT GROMMET TO SEAL THROUGH VEHICLE INTERIOR 3A Figure 6 11 1A TO MONITOR 18 TEW RED (12V) (MALE BULLET DISCONNECT) 18 TEW BLK (Ground) (FEMALE BULLET DISCONNECT) 18 TEW BLU (Reverse Trigger) (STRIPPED AND TINNED) 18 TEW YEL (Battery) (STRIPED AND TINNED) REAR OF MONITOR MONITOR FRONT VIEW A B 1 2 3 4 5 6 MONITOR REAR VIEW 4 3 2 1 Monitor Operating Controls and Connections 12 MICROPHONE MIRROR/ "NORMAL" SWITCH Camera Features 13 INDICATOR 3 FT. WIDTH OF VEHICLE MARKER'S EXAMPLE Figure 8 14 SPECIFICATIONS: AOS58 System, 1 Camera AOC75 Camera Rated Voltage Operating Voltage Current Consumption Sensitivity Signal System Image sensor Viewing Angle (approx. ) Outer Dimensions Weight 12VDC, Negative Ground 11 to 30 VDC 1. 5 Amperes 0. 1Lux NTSC 1/3" B/W CCD w/electronic auto-iris 270K picture elements 110° (H), 80° (V) 2. 44" (W) x 1. 50" (H) x 1. 96" (D) 6. 20cm (W) x 3. 81cm (H) x 4. 98cm (D) 0. 8 lbs. [. . . ]