User manual AVERATEC AVERATEC ALL-IN-ONE

[. . . ] DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Ethernet Notice This equipment is indoor use and all the communication wirings are limited to inside of the building. Before You Start iii Macrovision Notice This product incorporates copyright protection technology that is protected by U. S. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Safety Instructions 1. The openings on the enclosure are used for air convection and to prevent the equipment from overheating. [. . . ] Choose which jack (Headphone or Microphone) you have your external speakers connected to. When you finish the setting, click . Adjusting volume The Averatec All-In-One PC has built-in speakers on the base of the system. You can adjust the volume by clicking the volume adjustment buttons located on the front side of the PC and / or by using the volume control feature in Windows XP. Chapter 2 Getting Started 10 Using the Optical Drive The Averatec A1 PC is fitted with a slim-tray-loading optical drive (COMBO or DVD Recorder). Tray-loading CD drive 1. Insert CD/DVD Insert CD/DVD in the CD/DVD drive and place CD/DVD label upside front. Eject CD/DVD Press the Eject button of the CD/DVD drive on the left side of the Averatec A1 PC. You can then remove the CD/DVD. Chapter 2 Getting Started 11 Note  If you can not eject a CD/DVD from the drive, click Start, choose Computer, right-click on the CD/DVD drive that the CD/DVD is in and choose Eject in the popup menu.  If you can not eject a CD/DVD from the drive by pressing the eject button and choosing the Eject menu, insert the paper clip into the emergency eject hole as far as it will go then the tray will be slightly open. Pull out the tray and remove a CD/DVD from the tray. 2 1 3  Make sure CD/DVD is not inserted upside down. (CD label side facing toward upside of PC). Remove labels on CD/DVD for safe use. Chapter 2 Getting Started 12 Connecting to the Internet 1. Connect a LAN cable to the LAN connector as shown in the figure below. 2. Configure the communication settings for the system based on your communication environment. When connecting to the Internet via an internet service provider, contact the service provider for more information on required communication settings. Launch Internet Explorer or other communication software. Chapter 2 Getting Started 13 Using Your Webcam You can take photos and chat with your friends. Take photos To take photos, follow the next steps : 1. The CyberLink YouCam will be run and a green light on the webcam LED indicates your PC is ready to take photos. The cards are not inserted completely, the tip of the cards will remain out of the slot. (Insert cards with label side facing toward upside of the PC. ) Removing multi-media card To remove the card: 1. Grip the tip of the card and take it out from the slot. Insert cards with label side facing toward upside of the PC. MS-PRO Duo MMC RS-MMC SD MS-PRO MS Chapter 2 Getting Started 19 Using the Internal Microphone Your PC comes with a built-in internal microphone near the power button on the left of the computer. Use the built-in internal microphone to record sound for your webcam videos, and to use instant messenger or chat software to have video chats online. You can use the internal microphone from a distance of up to 1. 5 feet (one meter) from the Computer. Microphone Chapter 2 Getting Started 20 Chapter 3 21 System BIOS SETUP Chapter 3 System BIOS SETUP For System BIOS Setup, only change the items that you need. Note that incorrect settings of the BIOS Setup could result in a system malfunction. Entering into the System BIOS Setup After powering on the system, press <Del> to enter the System Setup screen. BIOS Action Keys Function Key ESC Enter F1 F10 <Tab> Exit Goto Sub Screen General Help Save and Exit Select a field Select an item -, + Change value Command Description Leaves a sub-menu to return to the previous menu OR exits the BIOS setup while saving changes. Shows the Sub Menu Shows the Help Screen Saves changes and reboots the computer. Selects the next value within a field. Chapter 3 System BIOS SETUP 22 BIOS Setup Menu Main Menu Sets most standard specifications for the system, such as the time, date. Advanced Menu Sets up key items related to the system’s performance. Chapter 3 System BIOS SETUP 23 Boot Menu You can set the boot sequemce. Security Menu Sets up a password to prevent any unauthorized user from accessing the system. Chapter 3 System BIOS SETUP 24 Set up Password 1. On the initial System Setup screen, Go to Change Supervisor Password, and then press <Enter>. On the following screen, enter the password and then press <Enter>. Enter New Password Confirm New Password Then enter the same password again and press <Enter>. [. . . ] Checking memory capacity Once memory installation is complete, restart the system. If an error message related to the memory capacity appears upon booting, press the Del key to enter the system setup screen. Save the setting and exit. Chapter 4 Expansion of the system 34 Using the Optional VESA Mount Kit Your system has four VESA Mount holes on the bottom surface for using the optional VESA Mount kit. Place LCD in down position and insert the hinge lock clip as shown below. Hinge lock clip Chapter 4 Expansion of the system 35 3. [. . . ]