User manual BDI ALCOVE 8200 CH ASSEMBLY
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BDI ALCOVE 8200 CH ASSEMBLY. We hope that this BDI ALCOVE 8200 CH ASSEMBLY user guide will be useful to you.
Manual abstract: user guide BDI ALCOVE 8200 CH ASSEMBLY
Detailed instructions for use are in the User's Guide.
[. . . ] HIGH PERFORMANCE FURNITURE FOR YOUR
HOME THEATER
Assembly Instructions
Alcove
TM
8200
AlcoveTM Home Theater Furniture
www. bdiusa. com
customerservice@bdiusa. com
Your AlcoveTM Home Theater Furniture is engineered for easy assembly. BDI strongly recommends two (2) people for successful product assembly. Placement and Maintenance AlcoveTM Home Theater Furniture is designed for indoor use on level floors. [. . . ] The height position can be adjusted up and down along the length of holes as needed to accommodate your desired viewing height and your specific TV.
This step is best performed with one (1) person holding the bracket in place from the FRONT of Alcove and one (1) person installing the bracket fasteners from the REAR of Alcove. Position 1" thick Styrofoam from original packaging on top of cabinet to protect it during assembly and installation of TV.
Fx8
Upper Bracket
Brackets have 5 holes on each side to allow fine-tuning of TV hanging position.
Hx1
Lower Bracket
Center channel speaker grommet. Designed to allow passage of wire connections and then grommet drops into place.
Position 1" thick Styrofoam from original packaging on top of cabinet to protect it during assembly and installation of TV.
Step 6
Install Flat Panel TV using Plasma Mounting Pack.
Horizontal Mounting Bar x 2
Plasma Mounting Hardware Pack
Phillips Head Mounting Screws (The following thread sizes are included: M4, M5, M6, M8. )
Black Washer x 8
Spacers x 8 (Large & Small)
Flanged Nut x 4
Step 6a
Install Horizontal Mounting Bars. If such screws are not available, find the short Phillips head mounting screws provided in the Plasma Mounting Blister Pack that thread cleanly into the mounting holes in the back of your TV. Attach upper and lower horizontal mounting bar to your TV, as shown, using washers and Phillips driver. Note: If back of TV has a curved surface or if bars do not rest flat, use spacers and long mounting screws provided. Fully tighten bars to TV!
Horizontal Mounting Bar
Flat Screen TV (Back view)
Short Mounting Screw Washer
Step 6b
Install TV with attached horizontal mounting bars to flat panel mounting brackets at desired height by inserting the threaded studs into key holes. Note: Flanged nuts are provided in the Plasma Mounting Blister Pack and must be threaded on the studs of the upper mounting bar in order to prevent any damage to the TV.
1
2
Step 6c
Once the threaded posts are positioned through the key holes and slots, lower TV into resting position. Tighten flanged nuts on upper mounting bar.
3
1
2
3
Install the second set of flanged nuts to the threaded posts of the lower mounting bar. Once positioned, fully tighten all flanged nuts!
Assembly complete!
Fine tuning your new BDI Alcove Home Theater Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Alcove stand. Due to jostling in freight or perhaps an uneven floor, the doors on your Alcove stand may not appear to be in perfect alignment (Refer to sample cabinet doors shown below). Be aware that depending on your situation, patience and a bit of trial and error are required. The high-quality European hinge hardware is infinitely adjustable, but changing one element can cause the need for further adjustments. Through a little adjustment, you can modify the orientation of the cabinet doors to make sure that they are sitting perfectly on your Alcove unit.
INCORRECT! [. . . ] · If adjusting Screw 1 has not achieved the desired result, you can adjust Screw 2 and the door will move up and down within the frame (the top and bottom hinges need to be adjusted the same amount). · Adjusting Screw 3 will cause the entire door to move in and out, opening and closing the gap between the door frame and cabinet. This screw rarely needs adjustment.
Step 1: Level your Alcove unit.
Step 2: Adjust Door Hinges.
HIGH PERFORMANCE FURNITURE [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BDI ALCOVE 8200 CH ASSEMBLY
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BDI ALCOVE 8200 CH ASSEMBLY will begin.