User manual BEAR ARCHERY COMPOUND

[. . . ] · Gainesville, FL 32608 352-376-2327 · fax 352-376-6115 www. escaladesports. com 1 Contents Archery Safety Bow Diagrams Maintenance Draw Weight Adjustment Xact Timing Adjustment Tiller Adjustment Draw Length Adjustment Modular Style Tri-Draw Style Perimeter Weighted OneCam SuperCam Extreme/Strike Cams HatchetCam Micro Perimeter Weighted Cam Original OneCam ActionCam Machlite Energy Wheel Rotating Module Cam Zen Cam Vortec Cam Initial Bow Setup Basic Tuning Care and Storage Bow Setup String Replacement Warranties 4&5 6&7 8&9 10 11 12 13 14 15 & 16 17 18 19 20 21 22 23 24 & 25 26 27 28 & 29 30 31 32, 33, 34 35, 36, 37 38 & 39 2 Congratulations!It has been engineered for accuracy and long life, and built with quality and pride. Regular waxing of string and buss cables reduces wear along with serving separations. Enjoy your new bow! Record important bow information here and keep for future reference: Model______________________________________ Weight Range _______________________________ Draw Length ________________________________ String Length ________________________________ Buss Cable and/or Cable Length ________________ Purchased From _____________________________ Date Purchased______________________________ 3 SAFETY FIRST Before using this equipment, read and follow these manufacturer's instructions carefully. [. . . ] To make such adjustments, a fixed or portable bow press should be used to relieve tension in the bow's harness system. To increase draw length, attach the bowstring to a lower numbered post. Going from post #2 to post #1 increases draw length by approximately 1/2 inch. To decrease draw length, attach the bowstring to a higher numbered post. Going from post #1 to post #3 decreased draw length by approximately 1 inch. Such bowstring post draw length adjustments will slightly affect the bow's draw weight. Most discrepancies in buss cable length can be adjusted for either by adding or removing twists from the buss cable or if larger changes are required then the buss cable attachment spool can be repositioned in the cam to one of its other locations. 21 ADJUSTING DRAW LENGTH ActionCam ActionCams are equipped with a modular draw length adjustment system. Draw length changes of plus or minus 1 inch are made by simply changing modules on both the top and bottom cam. When changing modules be sure that the module numbers are the same on top and bottom. There are two types of modules available for the ActionCam, wheel modules and cam modules. Your bow was shipped from the factory with the W2*, or middle, module installed. Cam modules are designated 65C1*, 65C2*, 65C3* and follow the same rules. To change modules remove the screw from the present module, remove that module and replace with the new module. Such modular draw length adjustment will not affect draw weight. 22 ADJUSTING DRAW LENGTH MachLite Energy Wheel Machine Lite Wheels are equipped with a bi-draw length adjustment system. Draw length changes are made by repositioning the bowstring, as it comes out of the wheel, into one of two different slots. To change draw length, it is first necessary to remove tension from the harness system of the bow by relaxing the bow in a bow press. Under no circumstances can this relaxing of the harness system be accomplished by simply backing out limb bolts. With the bow relaxed the bowstring can then be repositioned to the desired string slot. For the "middle" draw length, place string in "S" slot on one wheel and the "L" slot on the other wheel. Such bi-draw length adjustments will affect the bow's draw weight. A longer adjusted draw length will increase draw weight. 23 ADJUSTING DRAW LENGTH Rotating Module Cam Note the string side of the cam has 2 axle holes numbered 1 and 2 (Fig. This can be achieved either by relaxing the limb bolts or using a bow compressor. [. . . ] Warranty excludes strings, cables, cable slides and/or cosmetic appearances such as scratches, chips, dings, etc. Warranty extends to the original owner of the bow and is not transferable. In addition, the original owner must submit proof of the warranty information requirements to register the bow for warranty eligibility. Should the warranty information requirements not be provided, all repairs will be performed at 100% of the cost of parts and factory labor. [. . . ]