User manual BECKER 7802 DTM UPDATECD1 3

[. . . ] One-way streets, pedestrian zones, turning bans and other traffic regulations are taken into account as far as possible. There may be discrepancies between the data on the navigation CD and the actual local situation, due to permanent changes to road systems and their traffic regulations. Subject to errors and technical modifications 15 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Navigation with two European CDs A For example, if you wish to navigate from a town on the Southern Europe CD (D) to a town on the Northern Europe CD (B), enter your destination address as usual. After entering the town, you will be prompted to insert navigation CD No. [. . . ] In some cases, the speed limit indicated by the navigation system may be incorrect. At all times, the driver must decide whether or not to heed the speed limit indicated. We do not accept liability for erroneous data provided by the navigation system. !"! The navigation system will now prompt you to enter a name for the coordinates entered. Enter a name as described in the main instructions under "Entering a destination in the destination memory". Route guidance can now start. !  ! Set and confirm ! in the System Settings menu. F By pressing the right rotary control selection can be made between speed limits display or . Setting is confirmed and accepted by pressing and holding the right rotary control . Subject to errors and technical modifications 18 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X If, when the speed limit display is ON, you travel along a route with a speed limit and this speed limit is stored on the navigation CD, the corresponding symbol will appear on the right-hand side of the display indicating the speed limit. TV Y P Dynamic navigation with TMC Note: Dynamic route guidance is not possible in all countries. To use dynamic navigation and the functions described below, TMC must be switched on, as described under "Switching TMC on/off" on page 24. When any route recalculations are made with active dynamic route guidance, the navigation system may request the Navigation CD (if the Navigation CD is not already inserted). T The distance to the next point at which for example a turn should be made is displayed below the navigation arrow, which appears in reduced format. On routes with variable speed limits (dependent on weather conditions, time of day etc. ) a symbol with the text @5Y or a speed with an underscore (e. g. : "80") draws the driver's attention to the fact that the speed limit is variable. due to road works) are usually short-lived, these have not been included on the CD. Austria: The location and event code was made available by ASFINAG and BMVIT. Dynamic route guidance is used to calculate the route, taking current traffic announcements into account. The traffic announcements are transmitted by a TMC radio station in addition to the radio programme and are received and analysed by the navigation system. There is no charge for receiving traffic announcements. Subject to errors and technical modifications 19 Copyright by Becker GmbH, D-76303 Karlsbad Navigation CD 3. X Note: Traffic announcements are transmitted by radio stations, therefore we cannot accept any responsibility for the completeness and correctness of the announcements Note: If dynamic route guidance has been activated, the routes are calculated using the "fast route" setting. Activating dynamic route guidance Dynamic route guidance can be started by selecting !!S&Y Y in the route menu. Note: Can only be selected if TMC has been switched on or is currently switched on. See "Switching TMC on/ off" on page 24. If dynamic route guidance has been activated, a continuous check is made for the presence of relevant announcements for the selected route. The route is then calculated using the "fast route" option, while taking into account current traffic announcements. If the check determines that a traffic announcement is relevant for the route guidance, then a new route to the destination is calculated automatically by the unit. [. . . ] Deleting: Press the ;( , + ;( #63 !4* multifunction button. Switching on: Press the !4* multifunction button repeatedly until 6 5 is displayed. Switching off: Press the !4* multifunction button repeatedly until 6-- is displayed. Note: ! 1 1 E <;6:, 3, *; !7 ;( #63 !4* ! Using the right rotary control , select <;6:, 3, *; and press to confirm. [. . . ]