User manual BLUE CHIP AXON NGC 66

[. . . ] Table of Contents Quickstart Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 · Connecting your AXON to synths, sound modules, computer, mixer, amp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 · Powering up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 · AXON preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 · Navigating the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The "+1", "-1" keys will allow you to scroll through the six strings until you find the string you want to adjust. Use the arrow key to move the cursor onto the number you want to edit. Use the "+1", "-1" keys or the "+10", "-10" keys to adjust the value for the string. (The level at the top of the screen is your high E-string, at the bottom of the screen the low E-string. ) The editable numbers range from 16-64, where 16 is the least sensitive and 64 the most sensitive setting. For example, if you play loudly or if your pick-up is very close to the strings, you may want to set this value lower. If a string is set for a sensitivity level that is too high, you will see an overload message for that string when it is played. (should come close to the names of the strings on the right side of the screen) All six peak levels should be similar. If you adjust the level to the lowest possible value (16) and you still get an overload message, then your pick-up is too close to the strings and should be lowered. If a string is set for a sensitivity level that is too low, the level indicators will remain too far to the left of the screen. If you adjust the level to the highest possible value (64) and the level is still too low, then your pick-up is too far from the strings and should be raised. Position the cursor in the value to the right of SOURCE SCR: to set the Scratch number you want to copy. Using the +1, -1, +10, -10 keys, enter the Scratch number that you want to copy. Using the same process, set the value for the Scratch number to which you want to copy in the line DEST. If you decide you don't want to complete the copy, move the cursor to another line, and press OK. Position the cursor in the value to the right of SOURCE ARR: to set the Arrange number you want to copy. Using the +1, -1, +10, -10 keys, enter the Arrange number that you want to copy. Using the same process, set the value for the Arrange number you want to copy to in the line DEST. If you decide you don't want to complete the copy, move the cursor to another line, and press OK. Position the cursor in the value to the right of SOURCE ARR: to set the Arrange number you want to copy. Using the +1, -1, +10, -10 keys, enter the Arrange number that you want to copy. Using the same process, set the value for the Arrange number you want to copy to in the line DEST. If you decide you don't want to complete the copy, move the cursor to another line, and press OK. [. . . ] The "±" means that you are in the middle and can move the page in either direction behind your view window. At any point in the hierarchy of pages and lines, you may press one of the mode keys (Scratch, Arrange, Global, Chain) and move directly to the top page of that mode. If you are deep in the hierarchy of any mode and want to be immediately taken to the top page of that mode, then simply press the mode button again, although it is selected (the LED is lit) · Troubleshooting · Q: When I play the guitar, the Axon reacts with level meter response, but the synth does not play. Make sure MIDI cables are correctly connected: MIDI OUT on your Axon, MIDI IN on your synth 2. [. . . ]