User manual BMW DWA 5 SUPPLEMENTARY MANUAL

[. . . ] cycle, change its position, start You can customise the antiit without your permission, or theft alarm in certain ways to disconnect the battery will trig- suit your needs and preferger the alarm. the system is set in such a way that slight vibrations of the Note: motorcycle will not trigger a In order to protect the motorcyfalse alarm. cle's battery and ensure that Once you have activated the the engine can be started, the alarm, any attempted theft is alarm system deactivates itself indicated acoustically by the siren and visually by all four turn automatically a certain number indicators flashing at the same of days after being activated, altime, and the integrated immo- though it always remains active biliser suppresses engine start. for at least 7 days. L Introduction Controls 1 2 1 4 3 Overview and operation 4 5 1 2 3 4 5 Left button (ribbed) Right button LED Radio remote control unit Status LED (on the vehicle) Note: Do not be tempted to use the remote control unit to lock the keys inside a stowage compartment. [. . . ] Severe movements while the motorcycle is in transit could trigger a false alarm. You deactivate the motion sensor · by pressing button 1 on the remote control unit for a second time within the activation phase (b 12) Deactivation is confirmed · by the indicators flashing three times and · by the alarm tone sounding three times Alarm function Activation phases 3 12 Alarm function 15 seconds elapse before the alarm function is fully active. Status of the antitheft alarm Activation phase (15 seconds) LED Rapid flashing (0. 1 sec. off) Anti-theft alarm active How the alarm is triggered 1 2 3 13 Alarm An alarm lasts for 26 seconds. If the reason for the alarm persists, the alarm function is triggered again, but this can happen no more than five times in succession. You can cancel an alarm at any time after it has been triggered by pressing button 2 on your remote control unit. An acoustic alarm sounds and the turn indicators flash for the duration of the alarm. You can program the sound of the acoustic alarm (b 26). How the alarm is triggered The alarm can by triggered · by the motion sensor · by an attempt to switch on the ignition without deactivating the anti-theft alarm beforehand · by disconnection of the antitheft alarm from the motorcycle's battery (the anti-theft alarm's internal battery cuts in to supply power) Alarm function Deactivation 1 2 3 14 Alarm function Deactivating the alarm function with the remote control unit The alarm function is deactivated · by pressing button 2 on the remote control unit once If the alarm function was activated automatically beforehand when you switched off the ignition, it is reactivated 30 seconds later. Deactivation is confirmed · by the turn indicators flashing once and · by the alarm tone sounding once, if programmed (b 26) Deactivation Deactivating the alarm function without remote control unit If you do not have the remote control unit to hand when the anti-theft alarm is active, you can still deactivate the system. To do so, you will need the code number printed on your code card (b 6). 3 15 Note: The system will permit a maximum of 3 successive attempts; if the third attempt in succession is unsuccessful the antitheft alarm engages for 10 minDeactivation is confirmed utes. The cases remain locked · by the turn indicators flashing when the system is deactivated once without the remote control unit. and In this case you will have to re· by the alarm tone sounding sort to the emergency unlockonce, if programmed (b 26) ing routine (b 21). Step 1 2 3 Action Switch on the ignition Switch off the ignition and observe the LED Count the LED flashes until the number corresponds to the first digit of your code number. Switch on the ignition while the LED OFF LED is on Repeat steps 2 to 4 for each successive digit in your code number Confirmation Alarm is triggered LED flashing, alarm continues 4 5 Alarm function L Reasons for an alarm 3 16 Alarm function Reasons for an alarm Once you have deactivated the alarm function, the LED shows you reasons for alarms, if any, that were triggered in your absence: · Flashes 1x: Motion sensor · Flashes 2x: Ignition on while the anti-theft alarm was primed · Flashes 3x: Anti-theft alarm disconnected from motorcycle battery The LED ceases to output this signal after 1 minute, or as soon as you switch on the ignition. emergency unlocking routine. Emergency unlocking 4 21 If the compartments were locked by the central locking system and, for some reason, the remote control unit is not to hand, you can use the emergency unlocking routine to open them. Emergency unlocking is independent of the current status of the lock barrel. You cannot use the emergency unlocking routine to open the radio compartment. 2 Turn the key to the 45° position. 3 You can now press in the lock barrel with the key in order to open the lock. Note that the key cannot be removed from the lock barrel in this position. 4 You must turn the barrel to the unlocked position or the locked position in order to remove the key. The lock remains locked. Central locking system Safety shutdown 4 22 Central locking system Overly frequent locking and unlocking within a short period of time could cause the motors of the central locking system to become very warm. An override function can cut in and interrupt operation in order to avoid damage to the motors: these interruptions can last for a maximum of 30 seconds. Lights 1 a b c 5 23 The lights are switched on · when you deactivate the alarm function or · by switching off the ignition, if programmed (b 26) Map-reading light The map-reading light switches on automatically if switch 1 is in The lights dim out after position c. 20 seconds. Lights Customising the anti-theft alarm system 6 24 Programming You can customise the BMW anti-theft alarm system to suit your needs and preferences as follows: · Acoustic confirmation after activation/deactivation of the anti-theft alarm in addition to turn indicators flashing · Automatic activation of lights when ignition is switched off · Rising and falling (swelling) or intermittent acoustic alarm · Automatic activation of the alarm function when ignition is switched off Automatic activation of immobiliser when ignition is switched off Default settings 6 25 Setting Acoustic acknowledgement after activation/ deactivation Status OFF Automatic activation of lights when ignition is ON switched off Type of acoustic alarm Automatic activation of alarm function when ignition is switched off Intermittent OFF Automatic activation of immobiliser when igni- ON tion is switched off Programming Programming mode, accessing 1 2 6 26 Programming 5 Step 1 2 3 4 5 Action Deactivate the anti-theft alarm Steps 3 to 7 must be completed within 10 seconds Switch on the ignition Press button 2 once Switch off the ignition Confirmation Wait until LED 5 goes out LED lights up briefly LED shows the number of registered remote control units Indicators flash each time the button is pressed 3x acoustic acknowledgement 6 7 Press button 2 three times Switch on the ignition The programming function is now active. Programming The number of times LED 5 flashes indicates the step to which you have progressed in programming. An alarm tone sounds as confirmation when you press button 1, whereas an acknowledgement tone sounds when you press button 2. [. . . ] When this limit is reached the receiver on the motorcycle no longer reacts to signals from the remote control unit. The procedure for synchronisation is as follows: Step 1 2 3 4 5 Release buttons 1 and 2 Press button 1 or 2 Action Switch on the ignition Press and hold down buttons 1 LED 3 flashes and 2 LED 3 stops flashing after 10 seconds LED 3 on LED 3 off Confirmation Remote control units Changing the battery 1 2 8 34 3 Care and maintenance 4 Attention: Use only CR 2032 3V lithium batteries. The batteries in the remote con- Take care not to reverse polarity when inserting the batteries. trol units are due for replacement after approximately 2 to 3 Inserting batteries of a different years. You can tell when a bat- type or inserting the batteries with polarity reversed could tery is weak if LED 3 lights up only briefly, or not at all, when a cause irreparable damage to the device. [. . . ]