User manual BOSCH PIA611T66B INSTALLATION INSTRUCTIONS

[. . . ] Hob [en] Instructions for installation and use 3, $7 ‘  ‘  ‘  ‘  Ú Table of contents alon[e]Istrucifde INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing and connecting the hob - Figure 1/2/3/4/5 . . . . . . . . . . . 5 Connection drawing - Figure 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Removing the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTRUCTION MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Absence of pan or unsuitable size If no pan is placed on the selected hotplate, or if it is made of unsuitable material or is not the correct size, the power level displayed on the hotplate indicator will flash. If this takes more than 90 seconds, the hotplate will switch off automatically. Empty pans or those with a thin base Do not heat empty pans, nor use pans with a thin base. However, an empty pan may heat up so quickly that the "automatic switch off" function may not have time to react and the pan may reach very high temperatures. If it fails to work after it has cooled down, please contact the Technical Assistance Service. Pan detection Each hotplate has a minimum limit for detecting pans, which varies depending on the material of the pan being used. You should therefore use the hotplate that is most suitable for the diameter of your pan. ■ Suitable pans Ferromagnetic pans Only ferromagnetic pans are suitable for induction cooking, these may be made from: ■ ■ ■ enamelled steel cast iron special cutlery for stainless steel induction pan To determine whether a pan is suitable, check to see if a magnet will stick to it. Other suitable cookware for induction There are other types of cookware especially made for induction whose base is not entirely ferromagnetic. When using large cookware on a smaller ferromagnetic zone, only the ferromagnetic zone heats up, so heat might not be uniformly distributed. Cookware with aluminium on the base reduce the ferromagnetic zone, so less heat may be supplied or be difficult to detect. For good cooking results, the diameter of the cookware's ferromagnetic area should match the size of the hotplate. If cookware is not detected on a hotplate, try it on the next smaller hotplate down. 9 Familiarise yourself with the appliance These instructions for use are applicable to other hobs. On page 2 an overview of the models is provided, along with information on measurements. The control panel Control sur- Function faces Indicators % A /@ 0 @ @G Indicators Main switch Select power level Setting the time Childproof lock/Basic settings Powerboost x W › Duration of cooking time Timer Powerboost function Control surfaces Pressing a symbol activates its corresponding function. Notes ■ The settings will not change if several symbols are pressed at the same time. This enables the programming zone to be cleaned when food is spilt. ■ ‚-Š • /œ ‹‹ Power levels Residual heat Time program function Always keep the control surfaces dry. Moisture can affect proper functioning. The hotplates Hotplate Turning on and off Always use cookware of a suitable size. $ Single hotplate Use only cookware suitable for induction cooking; see the section on suitable cookware. Residual heat indicator The hob has a residual heat indicator for each hotplate to show those which are still hot. Even when switched off, the œ/• light will remain on as long as the hotplate remains hot. If the pan is removed before the hotplate is turned off the œ/• indicators and the selected power level will appear alternately. 10 Programming the hob This section will show you how to program the hotplates. Press the + or - symbol of the required hotplate and its Switching the hob on and off The hob is turned on and off using the main switch. To turn off: press the % symbol until the indicator above the main switch disappears. The residual heat indicator stays lit until the hotplates have cooled off. Note: The hob switches off automatically when all the hotplates are switched off for more than 20 seconds. display lights up ‹. 2. [. . . ] The electronic system has overheated and all the hotplates have been switched off. The hotplate has been working non-stop too long at a high power level. Please contact the local electricity board. The hotplate has overheated and has Wait until the electronic system has cooled down sufficiently before switched off in order to protect its cooking switching the hotplate back on. surface. * If the indication persists, call the Technical Assistance Service. [. . . ]