User manual BOSCH SPS40C12GB

[. . . ] 5HVHW  VHF       (QG K K K 6WDUW     (QG K K K               en Table of contents Half load . 15 15 15 15 15 15 16 16 16 16 16 16 17 17 17 17 18 18 19 19 20 20 20 21 22 22 22 23 23 23 23 23 24 24 24 24 25 25 25 Safety instructions . 15 en Safety instructions Before you switch ON the appliance Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance. [. . . ] Different influencing factors such as water temperature or mains pressure may result in deviations. auqArosne Ÿ Express Wash/ Speed Perfect/ (VarioSpeed) * This function can reduce the running time by approx. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased. Aqua sensor * Ï Intensive zone * vsIniezot ne Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. · Hygiene * egH yin * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. The temperature is increased during the cleaning process. chopping boards and baby bottles. fodH al Switching on the appliance – Turn on the tap fully. The programme starts running. § Half load * If you have only a few items to wash (e. g. It is recommended to put a little less detergent in the detergent dispenser than for a full load. ¿ Extra drying * nxEtradigy An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 15 en nargoTiep m Timer programming * Interrupting the programme – Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. nrem Tiatghpo * depending on model You can delay the start of the programme by 3, 6 or 9 hours. – Keep pressing the Preselected starting time button H until the appropriate display 3h, 6h or 9h is lit. – To delete the preselected starting time, keep pressing the Preselected starting time button H until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. Terminating the programme (Reset) – Press START button @ for approx. Switch off ON/OFF switch (. End of programme The programme has ended when the End display )" is lit. Note To save energy, the dishwasher automatically switches off after 2 minutes after the end of the programme. Changing the programme When the START button @ has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Remove the utensils when they have cooled down. ã=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. 16 en Intensive drying The final rinse uses a higher temperature which improves the drying result. [. . . ] Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out! Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. These will disappear after the first wash cycle. Technical specifications Weight: max. 45 kg Voltage: 220–240 V, 50 Hz or 60 Hz Connected load: 2. 0–2. 4 kW Fuse: 10/16 A (UK 13A) Water pressure: at least 0. 05 MPa (0. 5 bar), maximum 1 MPa (10 bar). Inlet rate: minimum 10 litres/minute Water temperature: cold water; hot water max. [. . . ]