User manual BOSCH TDS2021GB

[. . . ] • Remove the plug from the socket before pouring out the remaining water after use. • The appliance must never be placed directly under the tap to fill the water tank. • When placed on its stand, make sure that the surface on which the stand is placed is stable. • The iron must not be left unattended while it is connected to the supply mains. [. . . ] When the steam release button is activated, the steam generator will give three powerful shots of steam so that the steam reaches even deeper into the fabrics. 1. Set the temperature selector (14) on “• • •” 2. Press the steam release button (15) on the bottom of the handle two times shortly (double-click). or (model dependent) Shortly press the steam release button (16*) on the top of the handle. Remark : It is possible to stop the shots of steam by pressing the steam button shortly again. Intelligent steam (model dependent) This system has intelligent steam control, which, after releasing the steam release button (15), provides a small amount of additional steam. The additional steam can always be stopped by briefly pressing the steam release button once again. Ironing without steam 1. Begin ironing but without pressing the steam release button. Vertical steam 1. Set the temperature control to the “•••” or “max” position. 2. You can steam iron curtains and hanging garments (jackets, suits, coats. . . ) by placing the iron in a vertical position and pressing the steam release button. “Ultimate steam” function (model dependent) The “Ultimate steam” function helps to de-crease more stubborn materials found in garments like Jeans or linen tablecloth. When activating the “Ultimate steam” button (16*) the steam generator produces an extra amount of steam. The function should be used during intervals of a few seconds, to be the most effective. 1. set the temperature selector (14) on “•••” 2. press the “Ultimate steam” button (16*). Important: • The steam hose may get hot if you are ironing for long periods. • Note: Some water drops may appear when you use the “Pulse steam” or the “Ultimate steam” function for the first time. The water drops will disappear after you have used the function for some time. Never aim the steam at people or animals. Energy saving “eco” button (model dependent) If the “Energy saving” button (8*) is switched on, the energy consumption of the appliance will be reduced, by means of an automatic reduction of electricity and water consumption. A good ironing result will still be obtained for most of the garments. * model dependent  en Use the normal energy setting for thick and highly wrinkled fabrics. Note: If you work with the “Energy saving” function, the variable steam regulation and temperature regulation can still be used as recommended. Additional accessories (model dependent) Fabric protection soleplate cover The fabric-protection soleplate cover is used for steam ironing delicate garments at maximum temperature without damaging them. Use of the soleplate cover also does away with the need for a cloth to prevent shine on dark materials. It is advisable to first iron a small section on the inside of the garment to see if it is suitable. To attach the soleplate cover to the iron, place the tip of the iron into the end of the soleplate cover and pull the elastic strap over the lower rear of the iron until it fits tightly. To release the soleplate cover, pull the elastic strap and remove the iron. The fabric-protection soleplate cover may be purchased from the customer service or specialist shops: Accessory code (After-sales) 571510 Name of accessory (Specialist outlets) TDZ2045 Cleaning & Maintenance Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it. 1. After ironing, pull out the plug and allow the appliance to cool down before cleaning. 3. If the soleplate is soiled with dirt or scale, clean it with a damp cotton cloth. This procedure helps to remove scale particles out of the steam chamber. [. . . ] It is caused by the steam passing through the hose during steam ironing. Drainage plug located at the bottom of the appliance is loose. Water leakage from the boiler The iron does not stop • “Pulse steam” function may have • Just press the trigger once again and steaming after placing been activated by the double the iron will stop steaming at once. • The steaming will not stop centre. * model dependent If the above does not solve the problem, get in touch with an authorized technical service. Advice on disposal Our goods come in optimised packaging. This basically consists in using non-contaminating materials which should be handed over to the local waste disposal service as secondary raw materials. [. . . ]