Detailed instructions for use are in the User's Guide.
[. . . ] Slide one of the utility holes on the backstrap onto the support screw and fasten it with the spring washer and nut provided. Using the 5 x 25mm screw and the plain washer, secure the backstrap to the dashboard surface as shown in the diagram. Tighten, secure, and check the overall mounting to be sure it is safe and will not release in an emergency stop or other sudden movement of the vehicle.
mounting case support screw head unit Figure 1 Bending the support tabs
CD3125R/MP3-3130R User's Manual - page 2
English
Español
Português
Français
Deutsch
dashboard attachment surface support strap
DIN rear mount installation
(uses factory radio mounting bracket)
5mm nut spring washer plain washer 5 x 25mm support screw support screw
Select a position on the head unit housing where the screw holes of the factory radio bracket align with the threaded screw holes on sides of the head unit (Figure 3).
select two mounting hole positions on each side of head unit
Figure 2. Select mounting holes
Insert screws in two such locations on each side, and tighten securely (Figure 4). [. . . ] NOTE: For the rear-mount installation, do not use the trim piece, backstrap or mounting case.
use two mounting screws on each side
factory mounting bracket
factory bezel or dashboard opening
Figure 4. Insert screws and tighten
CD3125R/MP3-3130R User's Manual - page 3
English
Español
Português
Français
Deutsch
Detaching the front panel
Press the RELEASE button to release the panel from the right side of the head unit (Figure 5).
Be careful when handling the front panel!
1. Do not touch the contacts on the panel or the main unit body doing so may result in poor electrical contact.
RELEASE button
4. Do not attempt to disassemble the front panel.
Figure 5 Press RELEASE to release the front panel
Grasp the right side of the panel and pull to remove it (Figure 6).
Figure 6 Grasp the right side of the panel and pull to remove the panel
Immediately place the front panel in its protective case for safe and clean storage (Figure 7).
Front Panel
Figure 7 Place the front panel in its protective case
CD3125R/MP3-3130R User's Manual - page 4
English
Español
Português
Français
Deutsch
Reinserting the front panel
Push the front panel into the main body. You should hear a "click. " (Figure 8) NOTE: If the panel fails to lock into position properly, the function of some controls may be impaired, and some segments of the display may not become illuminated. If this occurs, press RELEASE and reinstall the front panel.
Removing the head unit
Should you need to remove the head unit, first remove and store the front panel as described on the preceding page. After you have removed the front panel, insert your fingers into the groove along the right side or the left side of the frame (not both!) and pull out to remove the bezel (Figure 9).
Figure 8 Push panel into main unit until you hear a "click"
Figure 9 Pull out to remove bezel
Then, insert the levers supplied with the head unit into the grooves on both sides of the unit as shown in the drawing until you feel a "click. " You can now use the levers to pull the unit from the dashboard (Figure 10).
Figure 10 Insert levers until "click" occurs, then use levels to pull out head unit.
CD3125R/MP3-3130R User's Manual - page 5
English
Español
Português
Français
Deutsch
General and Tuner Controls
1 23 4
5 10 6
9
8 1
7
General
Controls
Tu n e r
Controls
1 POWER
Press any button to turn unit on. Press and hold POWER to turn it off.
3 AS/PS
When pressed and held for several seconds, the tuner will search and store the first six strong stations as presets.
2 DISPLAY
To set CLOCK, press and hold, then press the TUNE/TRACK button.
5 LOCAL/DISTANT SELECT
Press to select between strong (LOC) and weak (DIST) stations.
4 RELEASE
Press to release and remove the front panel.
6 MONO/STEREO SELECT
Press if reception becomes noisy. Press again for normal stereo reception.
7 STATION PRESETS (1-6)
Press any preset to select a station. To store a station in memory, tune to it, and press and hold your choice of preset button for several seconds.
8 STATION SCAN
Press this button to make the tuner search the frequency band for stations, playing each for five seconds before moving to next station.
9 TUNE/TRACK BUTTONS
Press and release to activate automatic seek function ("AUTO" will appear on display). To enter a track number, use the buttons according to the chart below: Front panel control Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Source I<< >>I DISP Key assignment 1 2 3 4 5 6 7 8 9 0
SEARCH FILE NAME MODE Pressing the AS/PS button twice enters the Searching File Name mode. The unit searches for files whose names have the same characters inputted by the user. Front panel control Band/Loud Preset 1 Preset 2 Preset 3 Preset 4 Preset 5 Preset 6 Source I<< >>I Audio DISP Audio Up/Down Key assignment Enter A, B, C, 1 D, E, F, 2 G, H, I, 3 J, K, L, 4 M, N, O, 5/10 TRK DOWN P, Q, R, 6/10 TRK UP S, T, U, 7 V, W, X, 8 Y, Z, SPACE, 9 CHAR. SELECT (A-Z, 0-9)
NOTE: When in Normal Play mode and when in Searching File or Directory Mode, preset buttons 5 and 6 are assigned as 10 TRACK.
CHARACTER CHARACTER SHIFT SELECT RIGHT + (A-Z, 0-9)
CHARACTER SELECT (A-Z, 0-9)
5/10
6/10
TRACK DOWN TRACK UP
CD3125R/MP3-3130R User's Manual - page 10
English
Español
Português
Français
Deutsch
1
2
3
4
OUTLAW LAC129D Remote Control
1 POWER Use to turn CD Receiver
ON or OFF.
2 AUDIO Press the button repeatedly
to access Volume, Bass, Treble, Balance and Fader functions. Then use the I<< and >>I buttons to adjust the selected function.
13 12 11 10 5 6
3 VOLUME Use to increase or
decrease volume level.
4 SOURCE Press to choose desired
audio source (Radio, CD or AUX IN).
7
5 DISPLAY Use the I<< and >>I buttons
to set the clock.
6 AS/PS Use to automatically scan and
place six strong stations into memory.
7 PRESETS 1-6 Use to select preset
radio stations.
8 REPEAT Press and release to
continuously repeat same track. Press again to cancel the repeat function.
9
8
and )
13 TUNE/SEEK
(
9 CD SCAN Press to audition each
track on the current disc. Press again to play the current track.
10 SHUFFLE Press to play ALL tracks
on the CD in random order.
In Radio Mode, press and release to activate automatic seek function ("AUTO" will appear on display). Press and hold to engage manual tuning mode ("MANUL" will appear on display). In CD Mode, press and release to advance to the next track or to return to the beginning of the current track (track number will be displayed). To use the receiver as a head unit in a mobile audio system which includes an amplifier, use the RCA outputs to connect to the front, rear and subwoofer inputs of your amplifier(s).
Antenna connector RED
AUX IN (BLACK)
RIGHT CH (RED) LEFT CH (WHITE)
Ignition switch (ACC +)
Fuse
SUBWOOFER OUT (GREEN)
Memory backup YELLOW (BATT +) Ground (BATT -) BLACK
Choke Box
to amplifier inputs, if present FRONT RCA OUT (BROWN)
RIGHT CH (RED) LEFT CH (WHITE)
Power Antenna
BLUE
REAR RCA OUT (GREY)
RIGHT CH (RED) LEFT CH (WHITE)
LEFT FRONT SPEAKER + WHITE WHITE/BLACK
RIGHT FRONT SPEAKER GREY GREY/BLACK
LEFT REAR SPEAKER GREEN + GREEN/BLACK
RIGHT REAR SPEAKER VIOLET VIOLET/BLACK
CD3125R/MP3-3130R User's Manual - page 13
English
Español
Português
Français
Deutsch
Troubleshooting
If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. [. . . ] To use the receiver as a head unit in a mobile audio system which includes an amplifier, use the RCA outputs to connect to the front, rear and subwoofer inputs of your amplifier(s).
Antenna connector RED
AUX IN (BLACK)
RIGHT CH (RED) LEFT CH (WHITE)
Ignition switch (ACC +)
Fuse
SUBWOOFER OUT (GREEN)
Memory backup YELLOW (BATT +) Ground (BATT -) BLACK
Choke Box
to amplifier inputs, if present FRONT RCA OUT (BROWN)
RIGHT CH (RED) LEFT CH (WHITE)
Power Antenna
BLUE
REAR RCA OUT (GREY)
RIGHT CH (RED) LEFT CH (WHITE)
LEFT FRONT SPEAKER + WHITE WHITE/BLACK
RIGHT FRONT SPEAKER GREY GREY/BLACK
LEFT REAR SPEAKER GREEN + GREEN/BLACK
RIGHT REAR SPEAKER VIOLET VIOLET/BLACK
CD3125R/MP3-3130R User's Manual - page 13
English
Español
Português
Français
Deutsch
Troubleshooting
If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. If problems persist, read the following troubleshooting tips which may help eliminate the problems. REMEDY If the head unit is properly connected to the car accessory power circuits, but the engine is running, switch the ignition key to the "ACC" position. Leave player off for an hour or so, and then try again.
The fuse is blown. [. . . ]