User manual CHARMGLOW 720-0396

[. . . ] Stainless Steel Gas Grill USE AND CARE GUIDE MODEL NO. : 720-0396 ® ® FOR OUTDOOR USE ONLY Comsumer: Retain this manual for future reference. Installer: Leave this manual with consumer. PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE DO NOT RETURN TO PLACE OF PURCHASE SAFETY INSTRUCTIONS ***** WARNING ***** · If you smell gas: 1. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department · WARNING 1. Do not store or use gasoline or other flammable liquids OR vapors in the vicinity of this or any other appliance. [. . . ] USING ROTISSERIE BURNER: Your grill is capable of performing back burner rotisserie cooking. Light the rear burner as described in the lighting instructions, once lit, the rotisserie burner will reach cooking temperatures in about 1 minute. CAUTION: REMOVE THE WARMING RACK WHEN USING THE ROTISSERIE BURNER. THE HIGH HEAT COMING FROM THE BURNER MAY CAUSE THE WARMING RACK TO BEND. 17 LIGHTING INSTRUCTIONS WARNING: IMPORTANT!If there is evidence of cuts, wear, or abrasion, it must be replaced prior to use. Only the pressure regulator and hose assembly supplied with the unit should be used. If a replacement is necessary, contact the factory for proper replacement. Screw the regulator (type QCC1) onto the tank. Leak check the hose and regulator connections with a soap and water solution before operating the grill TO LIGHT THE GRILL BURNER: Make sure all knobs are "OFF" then turn on the gas supply from the LP tank. Always keep your face and body as far from the grill as possible when lighting. To ignite each burner simply push and turn the control knobs to the IGNITE/HI setting, you will hear the valve click as it sends a spark to the pilot flame. If the burner does not light, wait 5 minutes for any excess gas to dissipate and then retry. Each burner is adjusted prior to shipment; however, variations in the local gas supply may take minor adjustments necessary. Burner flames should be blue and stable with no yellow tips, excessive noise, or lifting. If any of Keep a spray bottle of soapy water near the gas supply valve and check the connections before each use. If the flame is noisy and tends to lift away from the burner, it indicates too much air. TO MATCH LIGHT THE GRILL: If the burner will not light after several attempts then the burner can be match lit. If you've just attempted to light the burner with the igniter, allow 5 minutes for any accumulated gas to dissipate. Insert a lit extended match or lighter through the cooking grids to the burner. Press the control knob and rotate left to the IGNITE/HI setting, continue to press the knob until the burner ignites. If the burner does not light in 4 seconds turn the knob off, wait 5 minutes and try again. TO LIGHT THE ROTISSERIE BURNER: Open the lid; push and turn the knob to the IGNITE/ON position while hold in the knob, push electronic igniter to light the rotisserie burner. Once the burner is lit, continue to hold in for another 15 seconds to be sure the burner stays lit. If the igniter does not function, follow the instruction above for match lighting. Do not attempt to light the grill if odor of gas is present. [. . . ] Please note the chart below to give an easy reference for the various orifice opening sizes for the different valves in the grill. Components Main Burner Side Burner Rear Burner Orifice Sizes and BTU Ratings Model Number 720-0396 LP NG Orifice Size BTU Orifice Size 0. 94 mm 10, 000 1. 55 mm 1. 02 mm 12, 000 1. 70 mm 0. 95 mm 10, 000 1. 55 mm BTU 10, 000 12, 000 10, 000 32 CONVERTING TO NATURAL GAS INSTRUCTIONS FOR CONVERTING TO NATURAL GAS Tools required for converting from LP to NG Screwdriver + is used for removing the screws 8mm Nut Driver is used for changing the main tube burner orifice Screwdriver - is used for turning the Low/High Flame 14mm Wrench is used for releasing the brass adapter of flex tube 10mm Wrench is used for changing the rear burner orifice Allen Key is used for removing the control knobs 18mm Wrench is used for fixing the side burner orifice nut (Included in package) 6. 1mm Wrench is used for changing the side burner orifice (Included in package) 33 GAS CONVERSION Main Tube Burner Conversion Steps 1. Remove the rotisserie kit, warming rack, cooking grids, flame tamers and tube burners from the firebox. 2. Locate orifice on end of valve and remove by turning counterclockwise with a 8mm Nut Driver. CAUTION! When converting the grill, screw the orifice in and out of the stem gently due to the breakable thread. 3. Replace tube burners back. 34 GAS CONVERSION Side Burner Conversion Steps 1. [. . . ]