User manual CORBERO FM1240S-2

[. . . ] AL ANU T M STE OOKLE E RVE HIS B E ONS EEP T C EA Y AND K L D REA FM 1100 S/2 (190****) FM 1240 S/2 (240****) FRIGRORIFICO CONGELADOR COMBINADO REFRIGERATOR- FREEZER COMBINATION ES GB MANUAL DE INSTRUCCIONES INSTRUCTION BOOK 200364377 SP/C/29-3. (04. ) GB Before installing and using the appliance read this user's instruction book carefully. If the refrigerator is used in compliance with the instructions written, it will operate properly and provide you with greatest satisfaction. The symbols below help you to find things more easily: Safety precautions Warnings and information at this symbol serve safety for you and your appliance. Hints, useful information Environmental information Symbol for ideas At this symbol ideas can be found according to food and its storing. From the Electrolux Group. The Electrolux Group is the world's largest producer of powered appliances for kifchen, cleaning and outdoor use. [. . . ] Information on your local disposal sites may be obtained from your municipal authorities. The materials used on this appliance marked with the sympol are recyclable. Maintenance Defrosting Bleeding part of the moisture of cooling chamber in form of frost and ice goes with the operation of the refrigerator. Thick frost and ice has an insulating effect, so it reduces cooling efficiency as the temperature increases, it needs more energy, at a certain thickness it does not allow the door of the frozen food compartment to open, possibly the door can be broken. At this type of appliance defrosting fresh food compartment is automatic without any external intervention. The thermostatic control interrupts the operation of compressor at regular intervals for more or less time during this cooling is interrupted - temperature of the fresh food compartment increases and defrosting occurs. After defrosting the thermostatic control restarts operation of the system. Melting water flows through defrost water outlet into the evaporative tray maintained on the top of compressor and evaporates due to warmth of it. Check and clean the outlet of melting water coming during defrosting regularly. If it is clogged the melting water gathered can cause earlier failure as it can go to the insulating of the appliance. Clean the melting water outlet with the supplied pipe scraper that can be seen in the figure. 24 GB The most typical case of clogging up in the defrost water outlet when you put food wrapped in some paper into the appliance and this paper contacts back plate of fresh food compartment and freezes to it. If you remove the food right at this moment the paper will tear and it can cause clogging up in the outlet by getting into it. So you are asked to be careful - because of the above - when placing foods wrapped in paper into the appliance. during heatwaves, the refrigerator temporarily happens to operate constantly. Remaining small ice and frost stains on back plate of the fresh food compartment after defrosting period is not abnormal. The frozen food compartment can not be equipped with automatic defrosting set since the deep-frozen and frozen foods do not endure melting temperature. So the enclosed plastic scraper is for scraping off and removing frost and ice coating which possibly occurs in the frozen food compartment and on the sealing of the door. When ice coating is so thick that it can not be removed with the plastic scraper, the frozen food compartment has to be defrosted (generally 2-3 times a year). Take the foods out of the frozen and fresh food compartment, wrap them into some layers of paper or cloth. Break the circuit of the appliance and leave the doors of frozen and fresh food compartment open. After defrosting wipe the surfaces, apply voltage to the appliance and put the foods back to their places. It is recommended to operate the appliance at the highest position of the thermostatic control so that it can reach the proper storing temperature as soon as possible. Regular cleaning It is recommended to wash the inside of the refrigerator in 3-4 weeks time. [. . . ] Fix the plate on the other side leaving the position of the door unchanged. Then screw in the one screw in the place set free on the other side as well as the adjustable feet (2 pieces) and set up the box. For refitting the upper door holder take out the screws (2 pieces) fixing the plastic top on the back of the box. After unscrewing turn over the pin in the door holder plate in the direction of the arrow. [. . . ]