User manual CORBERO LT4400

[. . . ] Make sure that the appliance does not stand on its electrical supply cable. If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely. It should have its own ventilation system which should not be joined with any other ventilation system connected to any other appliance. s s It is dangerous to modify or try to modify the specifications of this appliance in any way. Children should not be allowed to touch the controls or play with the product. [. . . ] 3 mm) in the lowest point of the hose and to place a small container below it. (See picture, point A). Once connected to the dryer, run the vent hose to the desired outlet point, ensuring that the run's overall length is less than 2 m, and that it contains no more than two bends. As to the outlet itself, if you have decided on a fixed wall/window grille, a good local builder's merchant should be able to supply you with the necessary fittings and installation advice. It is important not to connect the vent hose to, for example, a cooker hood, or a chimney or flue pipe designed to carry the exhaust from a fuel burning appliance. A P0279 P0055 Note that to avoid condensation problems, it is essential that the dryer be fitted with the flexible hose to carry its "exhaust" at least beyond the kitchen units; preferable outside the kitchen. In order to prevent the appliance from overheating, it is important that the steam exhaust is unobstructed. Therefore, in case of a permanent hose fitted to an exterior wall or ceiling, it must be ensured an exhaust capacity of at least 150 m3/h. If the dryer is fitted next to kitchen units, make sure that the vent hose is not squashed. If the hose is partially squashed, drying efficiency will be reduced, resulting in longer drying times and higher energy consumption. If the hose is completely squashed, the safety cut-outs with which the machine is fitted may operate. 6 Door reversal To make it easier to load or unload the laundry the door can be reversed. Operate as follows: - Remove the door by unscrewing the two screws (1) fastening the hinge to the cabinet (Fig. - Remove the safety catch (2) and the plug (3) by bending the two fastening tags (Fig. - Refit the safety catch (2) and plug (3) on the door by reversing their positions (Fig. - Remove the plastic plate (4) by unscrewing the two fastening screws (Fig. - Refit the door by screwing in the two screws (1) which fasten the door to the cabinet (Fig. B). 3 2 1 4 P0283 A 2 4 1 3 P0748 B Electrical connection This machine is designed to operate on a 220230 V, single-phase, 50 Hz supply. Check that your domestic electrical installation can take the maximum load required (2. 2 kW), also taking into account any other appliances in use. Connect the machine to an earthed socket, in accordance with current wiring regulations. The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Stacking kit A special stacking kit is available through your dealer, to enable the mounting of the dryer on top of your washing machine. P0280 7 ENGLISH USE Control panel ALGODON Y LINO EXTRA SECO SECO PARA GUARDAR SECO PARA PLANCHAR SINTETICOS SECO PARA GUARDAR D A B C LTE 4400 MARCHA BOTON REDUCCION TEMPERATURA BOTON DE EXCLUSION ALARMA BOTON START LUZ PILOTO DE SECADO LUZ PILOTO DE ENFRIAMIENTO LUZ PILOTO FIN DE PROGRAMA LUZ PILOTO PUERTA ABIERTA SELECTOR PROGRAMAS/ INTERRUPTOR MARCHA/PARADA SELECCION DEL TIEMPO 20-90 MIN. PROGRAMAS 1 23 45 67 8 9 10 1 Programme Chart This will help you to select the correct programme for drying. 7 End of Programme Light This light (red) comes on at the end of the drying programme and remains alight until the door is opened. This light will also remind you that the filter should be cleaned at the end of each drying cycle. 2 Low Temperature Button Press this button to reduce the temperature when drying particularly delicate items. To be used only when drying synthetics with the time controlled programme. 8 Open Door Light This light (red) flashes when the door is opened or not well closed. 3 Buzzer Off Button Press this button if you do not wish the buzzer to ring during the «anti-crease» phase. 9 Mains-On Light This lights up by selecting the programme or time and goes out when the programme selector dial is turned to «0». 4 Start Button Press this button for a few seconds to start the selected drying programme. If the door is opened during drying, this button has to be depressed after closing the door to allow the programme to continue. 10 Programme Selector Dial To set the machine to the selected programme or time, turn the dial until the letter or the time you want coincides exactly with the pointer. 5 Drying Light This light (green) indicates that the machine is performing the drying programme. 6 Cooling phase Light This light (green) will illuminate when the cooling phase is in operation. Load the items one at a time, shaking them out loosely and close the door. [. . . ] 30 seconds or using the special brief spin programme of your washing machine). 12 MAINTENANCE You must disconnect the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. External cleaning Use only soap and water and then dry thoroughly. From time to time, apply a little wax furniture cream with a soft cloth. Important: do not use methylated spirit, diluents or similar products. Cleaning the door Clean periodically the interior part of the door to remove any fluff. Accurate cleaning ensures correct drying. P0328 Cleaning the filter Your dryer will only function well if the filter is clean. [. . . ]