User manual CRESTON REMOTE ANNOTATION QUICK GUIDE
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CRESTON REMOTE ANNOTATION. We hope that this CRESTON REMOTE ANNOTATION user guide will be useful to you.
Manual abstract: user guide CRESTON REMOTE ANNOTATIONQUICK GUIDE
Detailed instructions for use are in the User's Guide.
[. . . ] Remote Annotation
quickstart guide
1
Introduction
Crestron® DVPHD High Definition Digital Video Processors, TPS and TPMC touchpanels allow annotation to be transmitted via Ethernet to multiple additional DVPHD, TPS and TPMC devices. Refer to the Crestron Web site (www. crestron. com) Answer ID 5047 for details on which models support remote annotation. [. . . ] Set the pad area channel (Serial Join) to match the Pad Area of the destination video object. NOTE: For a DVPHD as the destination, it can be Pad Area 1-8, so Serial Join would be 1-8. For a TPS or TPMC touchpanel as desination, it can be Pad Area 1 or 2, so Serial Join would be 1 or 2. Device ID can be set to anything, as it is needed for VT Pro-e but not for the device.
"Project Properties" Window for a DVPHD Processor "Video Properties" Window for a DVPHD Processor
NOTE: For a DVPHD the process is essentially the same, except that up to eight Pad Areas are available. Double-click the video object in the project to open its "Video Properties" window. The Touch/Pad Area must be set to match the corresponding setting in the "Project Properties" window, as shown in the illustrations below.
"Project Properties" Window for a TPS Touchpanel "Video Properties" Window for a TPS Touchpanel
6. The source device must add a peer IP table entry for each destination. Add a peer entry into the IP table with the addpeer command in the Crestron ToolboxTM console. For example: addpeer 03 192. 168. 1. 99
1
www. crestron. com QUICKSTART DOC. 7117A (2029317) 10. 10
©2010 Specifications subject to change without notice.
888. 273. 7876
201. 767. 3400
All brand names, product names, and trademarks are the property of their respective owners.
Remote Annotation
quickstart guide
3
Source Setup - TPMC (Example 192. 168. 1. 88)
Source setup for TPMC touchpanels is similar to that for DVPHD processors and TPS panels (refer to section "Source Setup - DVPHD and TPS") with three differences: 1. In the Touch/Pad Area section of the window, check the Enabled box.
"Project Properties" Window for a TPMC Touchpanel
3. Other setup parameters are selected using the Touchout extender for the panel in the SIMPLTM Windows program.
Touchout in SIMPL Windows
2. With TPMC touchpanels, peers can be added to the IP table by using the devices' internal setup menu.
Remote Annotation
4
Destination Setup (Example: 192. 168. 1. 99)
1. Create a VT Pro-e project with a video window object on a page and select a pad area in the object's properties. [. . . ] Perform annotation on the source and see that it is duplicated on the destination device(s).
2
www. crestron. com QUICKSTART DOC. 7117A (2029317) 10. 10
©2010 Specifications subject to change without notice.
888. 273. 7876
201. 767. 3400
All brand names, product names, and trademarks are the property of their respective owners. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CRESTON REMOTE ANNOTATION
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CRESTON REMOTE ANNOTATION will begin.