User manual DAHON TOURNEY REAR DRIVE SYSTEM TECHNICAL SERVICE INSTRUCTIONS
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DAHON TOURNEY REAR DRIVE SYSTEM. We hope that this DAHON TOURNEY REAR DRIVE SYSTEM user guide will be useful to you.
Manual abstract: user guide DAHON TOURNEY REAR DRIVE SYSTEMTECHNICAL SERVICE INSTRUCTIONS
Detailed instructions for use are in the User's Guide.
[. . . ] Next, set the chain to the 12 smallest sprocket and repeat the above to make sure that the B-tension 1 adjustment screw pulley does not touch the 1 sprocket.
Reinforced Connecting Pin · If it is necessary to adjust the length of the chain due to a change in the number of sprocket teeth, make the cut at some other place than the place where the chain has been joined using a reinforced connecting pin or an end pin. The chain will be damaged if it is cut at a place where it has been joined with a reinforced connecting pin or an end pin. · Check that the tension of the chain is correct and that the chain is not damaged. If the End Pin Link Pin tension is too weak or the chain is damaged, the chain should be replaced. [. . . ] If the chain is touching the 3rd sprocket and making noise, turn the outer casing adjustment barrel clockwise slightly to tighten it until the noise stops and the chain runs smoothly. Operate lever to change gears, and check that no noise occurs in any of the gear positions. For the best SIS performance, periodically lubricate all power-transmission parts.
Guide pulley
RD-FT30
Push in and tighten
5 mm Allen Key
Technical Service Instructions
SI-6KP0A
Tightening torque: 8 - 10 N·m {70 - 86 in. Connection and securing of cable
Rear Drive System
Installation of the freewheel
In order to realize the best performance, we recommend that the following combination be used.
Series Gears Shifting lever Outer casing Rear derailleur Multiple freewheel Chain Bottom bracket cable guide Right 7 - gears SL-RS43-7 SIS40 RD-TX70/RD-TX50 RD-TX30 MF-TZ37/HG50 MF-HG37/TZ07 CN-HG50 SM-SP18/BT18 6 - gears SL-RS43-6 SIS40 RD-TX70/RD-TX50 RD-TX30/RD-TY18 MF-HG40-6/HG22 MF-TZ06 CN-HG50 SM-SP18/BT18 Tourney 7 - gears SL-RS43-7 SIS40 RD-TX70/RD-TX50 RD-TX30 RD-FT30 MF-TZ37/TZ07 MF-HG50 CN-HG50 SM-SP18/BT18 6 - gears SL-RS43-6 SIS40 RD-TX70/RD-TX50 RD-TX30/RD-TY18 RD-FT30 MF-HG40-6/HG22 MF-TZ06 CN-HG50 SM-SP18/BT18
Tightening torque: 30 N·m {260 in. lbs. }
Connect the cable to the rear derailleur and, after taking up the initial slack in the cable, reattach to the rear derailleur as shown in the illustration. Secure the cable by pulling it with pliers with a force of 5 - 10 kg.
Tightening torque: 5 - 7 N·m {44 - 60 in. lbs. } Note: Be sure that the cable is securely in the groove.
To install
Freewheel removal tool
TL-FW30 Pull
Replacing the inner cable
Replace the inner cable by carrying out steps to as shown in the illustrations.
To disassemble
Groove
Inserting the inner cable
Insert the inner cable into the outer casing from the end with the marking on it. Apply grease from the end with the marking in order to maintain cable operating efficiency.
Marking
Chain length
< GS >
Add 2 links (with the chain on both the largest sprocket and the largest chainring)
Largest chainring Largest chainring
Cutting the outer casing < SS >
Smallest sprocket Largest chainring
When cutting the outer casing, cut the opposite end to the end with the marking. After cutting the outer casing, make the end round so that the inside of the hole has a uniform diameter. Attach the same outer end cap to the cut end of the outer casing.
Outer end cap
This service instruction explains how to use and maintain the Shimano bicycle parts which have been used on your new bicycle. For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of purchase or the bicycle manufacturer.
Chain Guide pulley Chain Tension pulley
One Holland, Irvine, California 92618, U. S. A. Phone: +1-949-951-5003 Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai, Osaka 590-8577, Japan
Right angle to the ground
Please note: specifications are subject to change for improvement without notice. XBC SZK Printed in Singapore
General Safety Information
WARNING
· Use neutral detergent to clean the chain. Do not use alkali-based or acid based detergent such as rust cleaners as it may result in damage and/or failure of the chain. · Use the reinforced connecting pin only for connecting the narrow type of chain. · There are two different types of reinforced connecting pins available. If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting pin or tool which is not suitable for the type of chain is used, sufficient connection force may not be obtained, which could cause the chain to break or fall off.
Chain 9-speed super narrow chain such as CN-7701 / CN-HG93 8- / 7- / 6-speed narrow chain such as CN-HG50 / CN-IG51 Reinforced connecting pin
Silver
6. 5mm
Specifications
Shifting lever
Model number Gears SL-RS43-L SIS 3 - gears
Installation of the front derailleur
1. · Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Front chainwheel
Model number Front chainwheel tooth combination Crank arm length Pedal thread dimensions Bottom bracket cup thread dimensions Applicable front derailleur FC-TX71 FC-TY33 48T-38T-28T 170mm BC 9/16" X 20 T. P. I. (68, 73 mm) FD-C051 FD-C051/TY30 FD-C051/TY30 FC-TS38A FC-TX70 FC-TY40 42T-34T-24T 170mm BC 9/16" X 20 T. P. I. (68, 73 mm) FD-C050 FD-C050/TY10 FD-C050/TY10 FC-TS32
Chainwheel (largest chainring)
4. Top adjustment
Set so that the clearance between the chain guide outer plate and the chain is 0 - 0. 5 mm.
FD-TY30 / TY10
3. Secure using a 9 mm spanner (TY30, TY10) or a 5 mm
Allen key (C051, C050).
Chain guide
Top adjustment screw
Tightening torque: 5 - 7 N·m {44 - 60 in. [. . . ] lbs. }
Inserting the inner cable
Insert the inner cable into the outer casing from the end with the marking on it. Apply grease from the end with the marking in order to maintain cable operating efficiency.
Tightening torque: 50 - 70 N·m {435 - 608 in. lbs. }
Adapter Bottom Bracket Marking
Tighten the low adjustment screw clockwise (about 1/2 turn).
Tourney 7 - gears 3 - gears SL-RS43-L SIS40 FD-C051/FD-TY30 FD-C050/FD-TY10 FC-TX70/TC-TX71/FC-TY33 FC-TS38A/FC-TY40/FC-TS32 BB-UN26 CN-HG50 SM-SP18/BT18
SHI
6 - gears 3 - gears SL-RS43-L SIS40
Replacing the inner cable
Replace the inner cable by carrying out steps to as shown in the illustrations.
Cutting the outer casing
When cutting the outer casing, cut the opposite end to the end with the marking. After cutting the outer casing, make the end round so that the inside of the hole has a uniform diameter. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DAHON TOURNEY REAR DRIVE SYSTEM
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DAHON TOURNEY REAR DRIVE SYSTEM will begin.