User manual EDIMAX BR-6324NL VERSION 1.0

[. . . ] No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this Company . This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. [. . . ] 2. 4 GHz (G): 2. 4GHz band, only allows 802. 11g wireless network client to connect this router (maximum transfer rate 54Mbps). 2. 4 GHz (B+G+N): 2. 4GHz Band, Allows 802. 11b, 802. 11g, and 802. 11N wireless clients. Select the channel number you wish to use; both access points must use the same channel. Input the MAC address of another wireless access point (the one you wish to connect). Click `Set Security' button to set security functions of this wireless connection to improve security. Please refer to chapter 3-2-1-7 for detailed instructions. Channel Number MAC address 1 Set Security When you finished with the settings in this page, you can click `Apply' button to save changes you made in this page, or you can click `Cancel' to discard changes. After you click `Apply' button, you'll see the following messages: Please click `Apply' to save changes you made and restart the broadband router, this requires about 30 seconds and the broadband router will stop responding (this is normal and is not malfunction). You can reconnect to this broadband router and continue on other settings later. You can click `Continue' to continue on other settings without restart the broadband router, however, the changes you made will not take effect before you restart the broadband router. 3-4-1-4 AP Bridge-Point to Multi-Point In this mode, you can use this broadband router as a wireless network bridge and let all computers connected to the LAN ports of all wireless access points to communicate with each other. Please note that when you select this mode, this broadband router will act as wireless bridge only, and will not accept other wireless clients. Also, you can connect to the wireless access point with the same functionality only. If you wish to connect to the wireless access points made by other manufacturer, please select `AP Bridge-WDS' mode if the wireless access point you wish to connect supports WDS. Here are descriptions of every setup items: Item Name Band Description Please select the radio band from one of following options (must be the same with the wireless access point you wish to connect): 2. 4 GHz (B): 2. 4GHz band, only allows 802. 11b wireless network client to connect this router (maximum transfer rate 11Mbps). 2. 4 GHz (N): 2. 4GHz band, only allows 802. 11n wireless network client to connect this router (maximum transfer rate 150Mbps). 2. 4 GHz (B+G): 2. 4GHz band, only allows 802. 11b and 802. 11g wireless network client to connect this router (maximum transfer rate 11Mbps for 802. 11b clients, and maximum 54Mbps for 802. 11g clients). 2. 4 GHz (G): 2. 4GHz band, only allows 802. 11g wireless network client to connect this router (maximum transfer rate 54Mbps). 2. 4 GHz (B+G+N): 2. 4GHz Band, Allows 802. 11b, 802. 11g, and 802. 11N wireless clients. Select the channel number you wish to use; all access points must use the same channel. Input the MAC address of other wireless access points (the access points you wish to connect). Click `Set Security' button to set security functions of this wireless connection to improve security. Please refer to chapter 3-2-1-7 for detailed instructions. Channel Number MAC address 1 to 4 Set Security When you finished with the settings in this page, you can click `Apply' button to save changes you made in this page, or you can click `Cancel' to discard changes. After you click `Apply' button, you'll see the following messages: Please click `Apply' to save changes you made and restart the broadband router, this requires about 30 seconds and the broadband router will stop responding (this is normal and is not malfunction). [. . . ] You can also click `View' to view current port-forwarding rules for this device. You can click `Refresh' button to rescan all UPnP-compatible devices on network, DMZ Port Forwarding When you finished with the settings in this page, you can click `Apply' button to save changes you made in this page, or you can click `Cancel' to discard changes. After you click `Apply' button, you'll see the following messages: Please click `Apply' to save changes you made and restart the broadband router, this requires about 30 seconds and the broadband router will stop responding (this is normal and is not malfunction). You can reconnect to this broadband router and continue on other settings later. Chapter V: Status In this menu, you can check the operation status of this broadband router. [. . . ]