User manual EPOX EP-3VCA

[. . . ] A Celeron TM Sock et 370 Pr ocessor k based 4X AGP motherboard (133/100/ 66MHz) Supports Suppor ts PC-133 SDRAM Module 3VCA 6VBA2 TRADEMARK A Pentium ® II or Pentium ® III Slot1 Pentium Pentium (133/100/66MHz) Supports Suppor ts PC-133 SDRAM Module Processor based 4X AGP motherboard All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subjected to change without notice. Manual Revision 1. 0 October 28, 1999 3VCA/6VBA2 Features FEATURES 3VCA/6VBA2 Features: · 3VCA is based on the Intel CeleronTM Processor operating at 300 ~ 600MHz on PGA370. The board is configured by an ESSJ (Easy-SettingSingle-Jumper) to match your CPU clock speed. [. . . ] With Flash Memory you can always upgrade to the current BIOS as they are released. (http://www. 2themax. com/ please visit our Technical Support section for the latest updates). · 3VCA/6VBA2 utilizes a Lithium battery which provides environmental protection and longer battery life. The onboard VT82C686A chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. · Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely). · Resume by Alarm - Allows your system to turn on at a preselected time. · Power Loss Recovery - In the event of a power outage your system will automatically turn itself back on without user intervention. · Supports CPU Hardware sleep and SMM (System Management Mode). · Built-in AC97 PCI Audio. Page 3 Installation 3VCA/6VBA2 3VCA Detailed Layout Page 4 Installation 3VCA/6VBA2 6VBA2 Detailed Layout Page 5 3VCA/6VBA2 Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configured Jumpers System memory Configuration Device Connectors Configure Jumpers We design this motherboard with the fewest jumpers to make your installation fast and easy. The following will describe all of the jumpers that you are required to set before moving on to step 2. SW1 ON SW1 1 ON ON ON ON ON ON 2 3 ON 4 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON Ratio 3X 3. 5X 4X 4. 5X 5X 5. 5X 6X 6. 5X 7X 7. 5X 8X CPU(MHz) 66MHz 200 233 266 300 333 366 400 433 466 500 *533 100MHz 300 350 400 450 500 550 600 *650 *700 *750 *800 133MHz 400 467 533 600 667 733 *800 *867 1234 *reserved JP1 C lear C O M S 1 -2 : N o rm a l(d efa u lt) 2 -3 : C lea r C M O S JP 4 K eyboard P ow er-O N F un ction Selection 1 -2 : D isa b led (d efa u lt) 2 -3 : E n a b led Page 6 Installation System Memory Configuration Memory Layout 3VCA/6VBA2 The 3VCA/6VBA2 supports (3) PC133 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized DRAM). · · · DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 125MHz (8ns) bus speed. [. . . ] When the system is in 4 sec delay mode, there is a special feature to make the system to go into suspend mode when the button is pressed momentarily). J3 1 Power On/Off Turbo LED indicator - LED ON when higher speed is selected + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks + is activate IR Connector 1. GND 1 Speaker - Connect to the system's speaker for beeping 1. [. . . ]