User manual EPOX EP-3WXM4
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual EPOX EP-3WXM4. We hope that this EPOX EP-3WXM4 user guide will be useful to you.
Manual abstract: user guide EPOX EP-3WXM4
Detailed instructions for use are in the User's Guide.
[. . . ] 3WXM4
Celeron Sock Processor A Celer on TM Socket 370 Pr ocessor based Intel 810 Chipset
motherboard (66/100MHz)
TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders.
These specifications are subjected to change without notice.
Manual Revision 3. 1 July 7, 1999
3WXM4
Features
FEATURES
3WXM4 Features:
· 3WXM4 is based on the Intel CeleronTM Processor operating at 300A ~ 466MHz (66MHz) or 100MHz FSB for feature processor on PPGA 370 socket. The board is configured by an Easy-Setting-Single-Jumper (E. S. S. J. ) to match your CPU clock speed. [. . . ] 3WXM4 utilizes a Lithium battery which provides environmental protection and longer battery life. The onboard ICH (82801) chip provides the means for connecting PC peripherals such as; keyboards, joysticks, speaker, and mouse. Supports ring-in feature (remote power-on through external modem, allow system to be turned on remotely. Supports Hot key, Any key or password Keyboard power ON function (KBPO). The Modem Riser Card (MR) or Modem Codec (MC) must be secondary only on the 3WXM4.
· · · · · · · · · ·
Page 3
Installation
3WXM4
3WXM4 Detailed Layout
Figure 1
Page 4
3WXM4
Installation
Easy Installation Procedure
Easy Installation Procedure
The following must be completed before powering on your new system: Configure Jumpers to match your hardware System Memory Configuration Device Connectors
Configure Jumpers
The 3WXM4 designs all motherboards with the fewest jumpers to make your installation fast and easy. The following will describe all of the jumpers that you are required to set before moving on to step 2. Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation.
JP1
1
CMOS Clear JP1 = 1-2 Normal (Default) = 2-3 Clear CMOS CPU Speed Selection
(Default) * Note: If CPU is S-Spec processor, than ignore the CPU ratio setting, otherwise the CPU ratio setting in BIOS (Frequency/Voltage Control). 1 Rsd: Reserved
JP3
Rsd 66MHz AUTO 100MHz
JP13
1
Keyboard Power-ON Function JP13= 1-2 Enabled = 2-3 Disabled (Default)
Page 5
Installation System Memory Configuration Memory Layout
3WXM4
The 3WXM4 supports (2) 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized DRAM). · · · · 100MHz system memory bus frequency. 8MB to 256MB using 16MB/64MB technology (512MB using 128MB technology). We recommend to installed the "PC/100MHz SDRAM Spec. ", using DIMM SDRAM must be 125MHz (-8ns) bus speed. [. . . ] When the system is in 4 sec delay mode, there is a special feature to make the system to go into suspend mode when the button is pressed momentarily. )
J3 1
Power On/Off
Turbo LED indicator - LED ON when higher speed is selected + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks +
is activate
IR Connector
1. GND
1 Speaker - Connect to the system's speaker for beeping
1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE EPOX EP-3WXM4
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual EPOX EP-3WXM4 will begin.