User manual EPOX EP-6VBA

[. . . ] 6VBA A Pentium ® II or Pentium® III Pentium Pentium Slot1 Processor based AGP Supports Suppor ts PC-133 SDRAM Module motherboard (100/66MHz) TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subjected to change without notice. Manual Revision 4. 2 May 25, 1999 6VBA Features FEATURES 6VBA Features: · 6VBA is based on the Pentium® II/III Processor operating at 266 ~ 550MHz on Slot1. The board is configured by an ESSJ (Easy-SettingSingle-Jumper) to match your CPU clock speed. · Designed with VIA Apollo Pro PCIset. [. . . ] (http://www. 2themax. com/ please visit our Technical Support section for the latest updates) · 6VBA utilizes a Lithium battery which provides environmental protection and longer battery life. Page 2 Features 6VBA · Supports the (4) Universal Serial Bus (USB) Ports. The onboard VT82C686A chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. · Built-in ATX 20-pin power supply connector. · Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely. · Resume by Alarm - Allows your system to turn on at a preselected time. · Power Loss Recovery - In the event of a power outage your system will automatically turn itself back on without user intervention. · Supports CPU Hardware sleep and SMM (System Management Mode). · Supports Keyboard power ON function (KBPO). · Built-in AC97 PCI Audio. Page 3 Installation 6VBA 6VBA Detailed Layout Figure 1 Page 4 6VBA Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure DIP Switch and Jumper to match your hardware System memory Configuration Device Connectors Configure DIP Switch We design this motherboard with a DIP Switch to make your install fast and easy. The following will describe all of the DIP Switch that you are required to set before moving on to step 2. Note: The DIP Switch as depicted as shown (Figure 1) in their correct physical orientation. ON 1234 1 ON ON ON ON 2 SW1 3 ON 4 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON Ratio 3X 3. 5X 4X 4. 5X 5X 5. 5X 6X 6. 5X 7X 7. 5X 8X CPU(MHz) 66MHz 200 233 266 300 333 366 400 433 *466 *500 *533 100MHz 300 350 400 450 500 *550 *600 *650 *700 *750 *800 *reserved JP1 C lea r C O M S 1 -2 : R un M o d e(d efau lt) 2 -3 : C lea r C M O S K eyboa rd P o w er-O N F u n ction Se le ction 1 -2 : D is a b le d 2 -3 : E n a b le d JP 4 Page 5 Installation 6VBA System Memory Configuration Memory Layout The 6VBA supports (3) 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized DRAM). · · · DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 125MHz (8ns) bus speed. If you use both 50ns and 60ns memory you must configure your BIOS to read 60ns. [. . . ] When the system is in 4 sec delay mode, there is a special feature to make the system to go into suspend mode when the button is pressed momentarily. ) Power On/Off Turbo LED indicator - LED ON when higher speed is selected + + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is activate IR Connector 1. GND 1 Speaker - Connect to the system's speaker for beeping 1. [. . . ]