User manual EPOX EP-BX6

[. . . ] Pentium II/III/Celeron A Pentium ® II/III/Celer on Slot1 Processor based AGP BX6 motherboard TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subjected to change without notice. Manual Revision 1. 0 Feb. [. . . ] (http://www. 2themax. com · · · · · please visit our Technical Support section for the latest updates). Page 2 Features · · BX6 BX6 utilizes a Lithium battery which provides environmental protec- tion and longer battery life. The onboard PIIX4E chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. Supports ring-in feature (remote power-on through external modem, allow system to be turned on remotely). Resume by Alarm - Allow your system to turn on at a preselected time. Power Loss Recovery - In the event of a power outage your system will · · · · · · · automatically turn itself back on without user intervention. Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (optional) Supports Hot key, Any key or password Keyboard power ON function (KBPO). Supports USDM software to allow the status monitoring of various aspects of the system when using Windows® 95/98 or Windows® NT 4. 0. Supports the STR (Suspend To RAM) power management by ACPI's S3. Supports the STR indicator red LED (D8) to avoid plugging or un-plugging · · · · · · · · DIMM modules when in a STR mode. Built-in WOL (Wake On Lan) Connector. Page 3 Installation BX6 BX6 Detailed Layout Figure 1 Page 4 BX6 Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure Jumpers System memory Configuration Device Connectors Configure Settings The following will describe all of the setting that you are required to set before moving on to step 2. ROM PCI/ISA BIOS(2A69KPAI) SENSOR & CPU SPEED SETTING AWARD SOFTWARE, INC. Auto Detect DIMM/PCI Clk Spread Spectrum Modulated CPU Host Clock CPU/PCI Clk Ratio CPU/AGP Clk Ratio CPU Int Clk Ratio CPU Clk Frequency CPU:AGP (Clk:Clk) CPU:PCI (Clk:Clk) CPU Vio Voltage CPU Vcore Voltage CPU Vcore Voltage : Enabled : Disabled CPU Warning Temperature Extended JP2 Temperature Current CPU Temperature Current System Temperature Current POWER FAN Speed Current CPU FAN Speed Current CHASSIS FAN Speed Vcore : 2. 10V Vtt(V) Vio(V) : 3. 47V +5V +12V : 12. 40V -12V -5V : -5. 50V VBAT (V) 5VSB (V) : 5. 08V Shutdown Temperature : 95OC/205OC : 0OC/32OC : 0OC/32OC : 0OC/32OC : 4900 RPM : 4900 RPM : 4900 RPM : 1. 55V : 5. 02V : -11. 95V : 3. 44V : 100OC/167OC : Default : Auto : Auto : x3 : 300(100x3) MHz : 3:2 (100:66) : 3:1 (100:33) : 3. 40V : +0. 10V : 2. 10V é ê è ç Select Item Esc:Quit : F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift) F2 : Color F7 : Load Setup Defaults Page 5 Installation CPU Type External Clock Ratio 2. 0 2. 5 3. 0 3. 5 4. 0 4. 5 5. 0 5. 5 6. 0 6. 5 7. 0 7. 5 8. 0 BX6 Slot1 Type Pentium II Pentium III Celeron S370+Convert Card 66 or 100 Note: Based on the implementation of the Intel 440BX AGPset, the BX6 is able to provide multiple front side bus (FSB) frequencies for Slot 1 processors and memory operations. The motherboard's FSB is easily se- lected by BIOS Setup listed above to match the FSB required by your processor. When using the 100MHz FSB (or higher) you must use PC100 (or better) compliant SDRAM. When selecting memory for use on the 2themax brand motherboard we recommend use only the finest quality modules. 2themax would like to stress that using non-compliant PC100 SDRAM modules with a 100MHz (or higher) FSB severely compromises the integrity of the system. JP 1 1 C h a ssis (C ase) in tru d er d etect JP 1 = 1 -2 - N o rm al (D e fau lt) = 2-3 - C lea r C M O S (m o m en ta rily) JP 2 1 C M O S C lear JP 1 = 1 -2 - N o rm al (D e fau lt) = 2-3 - C lea r C M O S (m o m en ta rily) JP 4 1 K eyb oa rd P ow er -O N fu n ction JP 4 = 1 -2 - E nab led = 2-3 - D isab led (D efau lt) Page 6 BX6 Installation JJPPX 11& J P X 2 X 1 & JPX 2 1 T h e F ifth o r Six th P C I M a ster S elect = 1 -2 - S ix th S la v e (D efa u lt) = 2 -3 - S ix th M a ster J1 S B -L IN K C o n n ector R eserv ed for C reativ e S B -L IN K (S oun d B laste r L IN K ) w ith th e S o un d B laster AW E 6 4D P C I S o u n d C ard to com p atib le TM TM J7 W O L (W a k e O n L a n ) C on n ecto r R eserv ed for N IC (N etw o rk In terface C a rd ) to W ak e th e S y ste m . LED1 LED2 Debug card on board (Please refer to Appendix B for POST codes) Page 7 Installation BX6 System Memory Configuration Memory Layout The BX6 supports (3) 168-pin DIMMs (Dual In-line Memory Module). [. . . ] IRTX 1 J2 KeyLock - Keyboard lock switch & Power LED connector 1. GND 1 Speaker - Connect to the system's speaker for beeping 1. [. . . ]