User manual EPSON SPECTROPROOFER MOUNTER 17 INCH

[. . . ] . 5 . 5 . 6 . 7 . 7 . 7 . 7 Where To Get Help Technical Support Web Site. 19 3 SpectroProofer Mounter 17" User's Guide Safety Instructions Safety Instructions Safety Instructions Read all of these instructions before using your product. Also be sure to follow all warnings and instructions marked on the product. Except as specifically explained in your documentation, do not attempt to service the product yourself. [. . . ] U See "Supported Media" on page 9 Start the SpectroProofer Utilities. U See "Starting SpectroProofer Utilities" on page 11 12 SpectroProofer Mounter 17" User's Guide Maintenance Maintenance To keep the product in good working condition, we recommend cleaning the parts. B Unplug the two interface cables connected with ILS20EP/ILS20EPUV. Cleaning procedures Cleaning the ILS20EP/ ILS20EPUV A Turn off the printer, and then open the front cover of the mounter. C Hold the front of ILS20EP/ILS20EPUV and lift the rear a little, and then remove it. c Caution: or knock it against hard objects. Do not drop The lens may be scratched or ILS20EP/ ILS20EPUV may be damaged. 13 SpectroProofer Mounter 17" User's Guide Maintenance D Use air to blow any dust and dirt off the lens in ILS20EP/ILS20EPUV. B Remove the mounter. w Warning: flammable gas spray inside or Do not use around this product. C Turn the mounter around, and then remove the backing or the white calibration tile holder. c Caution: the lens directly in ILS20EP/ Do not touch ILS20EPUV. E Install ILS20EP/ILS20EPUV in the mounter, and then close the front cover of the mounter. U See the SpectroProofer Mounter 17" Setup Guide Cleaning the surface of the backing/white calibration tile c Caution:the backing is fragile, do not drop or Because knock it against hard objects. A Open the side cover, and then unplug the printer connection cable. 14 SpectroProofer Mounter 17" User's Guide Maintenance D Remove the white calibration tile from the white calibration tile holder. Cleaning the paper presser A Turn off the printer, and then open the front cover of the mounter. E Use a soft, dry cloth to carefully remove any dust or dirt from the surface of the white calibration tile or the surface of the backing. If the dirt does not come off, soak a soft cloth in water and wring it dry, and then rub away any dirt from the surface. Then, wipe the surface again with a soft, dry cloth. B F See the SpectroProofer Mounter 17" Setup Guide to setup the mounter. U See the SpectroProofer Mounter 17" Setup Guide Hold both ends of the paper presser and lower it forward. C Soak a soft cloth in water with a small amount of mild detergent, wring it dry, and then wipe away dirt from the base (the surface that touches the paper) of the paper presser. Then, wipe it with a soft, dry cloth. 15 SpectroProofer Mounter 17" User's Guide Maintenance C Remove the paper guide unit, and then wipe away the powdery paper. D D Close the front cover of the mounter. Replace the paper guide unit, install the mounter, and then connect the printer connection cable. U See the SpectroProofer Mounter 17" Setup Guide Cleaning the paper guide unit Some powdery paper accumulates in the paper guide unit when the printer cuts paper using the auto cutter. Use the following procedure to periodically clean up the powdery paper (about once a month). A Open the side cover, and then unplug the printer connection cable. B Remove the mounter. 16 SpectroProofer Mounter 17" User's Guide Troubleshooting Troubleshooting When Error Message Appears When an error occurs in the printer (or when the printer enters an abnormal status), the large alert light on the printer and a light on the control panel are lit, and a message is displayed on the LCD panel. When the error message appears, check the following solutions and do the required action. Error message SpectroProofer Error Refer to the manual to find out how to solve the problem. XX (where XX indicates the error number) What to do Check the error number, and then take the following action. For error number 01 Turn off the printer, and then remove the mounter. U See "Maintenance" on page 13 U See the SpectroProofer Mounter 17" Setup Guide If the error continues to occur, contact customer support services for assistance. If customer support for your area is not listed below, contact the dealer where you purchased your product. U See "Where To Get Help" on page 22 For error number 02 Turn off the printer, remove the mounter, and then install the paper guide unit correctly. U See the SpectroProofer Mounter 17" Setup Guide For error number 13 or 15 Turn off the printer, and then remove the mounter. Remove any packing materials or foreign objects around the backing if any, and then reset the backing correctly. U See "Maintenance" on page 13 U See the SpectroProofer Mounter 17" Setup Guide Or, check that the paper type and usage conditions are compatible with the specifications. U See "Supported Media" on page 9 U See "Specifications" on page 20 If the error continues to occur, contact customer support services for assistance. If customer support for your area is not listed below, contact the dealer where you purchased your product. U See "Where To Get Help" on page 22 For error numbers other than the above Make a note of the number displayed and contact customer support services for assistance. [. . . ] Arteri Mangga Dua, Jakarta Phone/Fax: (62) 21-62301104 Bandung Lippo Center 8th floor Jl. Gatot Subroto No. 2 Bandung Phone/Fax: (62) 22-7303766 Epson Hotline (Phone: (66)2685-9899) Our Hotline team can help you with the following over the phone: Sales enquiries and product information Product usage questions or problems Enquiries on repair service and warranty 24 SpectroProofer Mounter 17" User's Guide Where To Get Help Surabaya Hitech Mall lt IIB No. Kusuma Bangsa 116 ­ 118 Surabaya Phone: (62) 31-5355035 Fax: (62)31-5477837 Phone: Fax: (852) 2827-8911 (852) 2827-4383 Yogyakarta Hotel Natour Garuda Jl. 60 Yogyakarta Phone: (62) 274-565478 Help for Users in Malaysia Contacts for information, support, and services are: Medan Wisma HSBC 4th floor Jl. [. . . ]