User manual EPSON SURECOLOR SC-F9200 SETUP GUIDE

[. . . ] ❏ Wear protective eyewear, gloves, and a mask when refilling ink tanks or replacing the Waste Ink Bottle. Should ink contact your skin or enter your eyes or mouth, immediately take the following actions: -- If fluid adheres to your skin, immediately wash it off using large volumes of soapy water. Failure to observe this precaution could result in bloodshot eyes or mild inflammation. [. . . ] When moving the printer, rotate the stand fixing screws in the opposite direction to raise them and then unlock the casters. 16 EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [5]   English  /  Français  /  Deutsch  /  Nederlands  /  Italiano  /  Español  /  Português  [6] [7] When reassembling the printer and legs after transporting, you need the parts that you removed during disassembly. Cuidado Be careful not to trap your hands or fingers when opening or closing the front cover. [9] Pressing the tabs on the sides of the media holding plates as shown, position the plates temporarily in the center of the platen. 3 kg) using two persons, each holding the two bars as shown in the figure on the right. C 19   English  /  Français  /  Deutsch  /  Nederlands  /  Italiano  /  Español  /  Português  Media Feeding Unit EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [3] [4] Keep the four screws in the figure on the right provisionally tightened until parallel adjustment is completed. 3 kg) using two persons, each holding the two bars as shown in the figure on the right. 22 EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [3] 5   English  /  Français  /  Deutsch  /  Nederlands  /  Italiano  /  Español  /  Português  [4] Keep the four screws in the figure on the left provisionally tightened until parallel adjustment is completed. 23 EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [5] Media Guide Bar Barre de guidage du support Medienführungsschiene Materiaalgeleider Barra della guida di supporto Tensor Barra guia de papel [1] Temporarily fasten the two screws as shown in the figure. C 24 EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [2] Fully tighten the two screws that you provisionally tightened. 25   English  /  Français  /  Deutsch  /  Nederlands  /  Italiano  /  Español  /  Português  EN Assembly FR Assemblage DE Montage NL Montage IT Montaggio ES Montaje PT Montagem [5] Fully tighten the two screws that you provisionally tightened. Do not turn the printer on until the service engineer’s work is complete. Attempting to perform these tasks yourself could result in product malfunction or damage to the product and will void the product warranty. [7] Keep the two screws shown in the figure temporarily tightened until the parallel adjustment is completed. [. . . ] We recommend that you press the r button in the control panel and set Media Suction to 2. 38 EN Loading Media FR Chargement des supports DE Einlegen von Medien NL Media invoeren IT Caricamento supporto ES Carga de materiales PT Carregar Papel [15] [16]   English  /  Français  /  Deutsch  /  Nederlands  /  Italiano  /  Español  /  Português  [17] Pressing the tabs on the sides of the media holding plates, slide the plates to the edges of the media. 39 EN Loading Media FR Chargement des supports DE Einlegen von Medien NL Media invoeren IT Caricamento supporto ES Carga de materiales PT Carregar Papel [18] Position the left and right plates so that the edges of the media can be seen at the centers of all three holes. [. . . ]