User manual FUTABA 3PM-2.4G MX

[. . . ] 3PM-2. 4G MX 3-channel, FASST Radio control system for Car INSTRUCTION MANUAL 1M23N13518 R Digital Proportional R/C System Thank you for purchasing a Futaba 3PM-2. 4G MX system. Before using your 3PM-2. 4G MX system, read this manual carefully in order to use your R/C set safely. After reading this manual, store it in a safe place. Application, Export, and Modification 1. It is not intended for use in any application other than the control of models for hobby and recreational purposes. [. . . ] LED and F/S switch LED status vs transmitter's condition: Parameter check for 0. 5 seconds after power-on Transmitting signals F/S is activated by the F/S switch of the transmitter. When the link is complete, the LED in the receiver changes to solid green. *Please refer the table below for LED status vs receiver's condition. 24 Initial Set-Up LED status vs receiver's condition: No signal reception Receiving signals Receiving signals, but ID is unmatched. Red : On Green: On Green: Blink How to Set the F/S Position (PPM mode) PPM mode only: *HRS mode: Set the F/S function by the fail safe function menu. 1. Move and hold the throttle trigger to the F/S servo position you want to set (slow side). Then push the F/S switch on the transmitter. *The LED blinks green. LED and F/S switch Note: Always set the F/S position when turning on the transmitter power. Preparations (Transmitter) Before setting the transmitter functions, check and set items below. (Display when power switch is turned on) Turn on the transmitter power. Signal mode PP: PPM mode HRS: HRS mode (displayed for about one second) Battery voltage Model name Model number 1. Model Number Check When the power switch is turned on, the current selected model number is displayed. To change the model number, use the Model Select function (page 50). 2. Signal Mode Check The T3PM-2. 4G MX transmitter output signal format can be changed. If this setting is incorrect, change it with the HRS/PPM Select function (page 55). Initial Set-Up 25 3. Trims Initial Set-Up - Steering trim (DT1) check At initial set-up, steering trim is assigned to digital trim DT1 above the steering wheel. Operate the DT1 lever and check if the steering trim value on the screen changes. After checking the trim, set the trim value to the center (0) position. - Throttle trim (DT2) check At initial set-up, throttle trim is assigned to digital trim DT2 at the left side of the steering wheel. Operate the DT2 lever and check if the throttle trim value on the screen changes. After checking the trim, set the trim value to the center (0) position. DT1 Steering trim Throttle trim position position DT2 26 Initial Set-Up - Steering dual rate (DT3) check At initial set-up, steering dual rate is assigned to grip lever DT3 (upper) at the grip of the transmitter. Operate the DT3 lever and check if the D/R value displayed on the screen changes. - Throttle ATL (DT4) check At initial setting, throttle ATL is assigned to grip lever DT4 (lower) at the grip of the transmitter. Operate the DT4 lever and check if the ATL value displayed on the screen changes. After checking ATL, set throttle ATL to 100%. Steering D/R Throttle ATL position value DT3 DT4 (Set-Up Procedure When Installed In a Car) When installing the servos in a car, performing function set-up in the following order is recommended. (Page 49) The servo installation method and linkage direction depend on the kit. Therefore, the servo operation direction may have to be reversed relative to transmitter operation. [. . . ] Set the vacant digital trims to the 3rd channel at the function select setup screen. (3P: 3 position switch, 2P: 2 position switch) Calling the setup screen 1. Next, use "SEL" key to select the desired function screen. Press "CH" key to select the next setup screen. Trim step adjustment 58 Functions 1 (Setup item selection) Use the (CH) button to select the item to be set. 2 (Trim step adjustment) Use the (+) or (-) button to adjust the trim step amount. 3 When ending adjustment, turn off the power switch before use. Condition 2 Selection / COND2 Condition 2 Selection In specific functions, two rates can be set up, and switched with the switch (SW1) simultaneously during a run. If this function is activated, SW1 is used only for this function, and it becomes impossible to use it for other functions automatically. [. . . ]