User manual FUTABA 3VCS

[. . . ] Prior to operating your 3VCS, please read this manual thoroughly and use your system in a safe manner. See the glossary on page (P110-112) for the definition's of the special terms used in this manual. Application, Export and Reconstruction 1. The product described in this manual is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes. Exportation Precautions (a) When this product is exported from Japan, its use is to be approved by the Radio Law of the country of the destination. [. . . ] 4 When ending adjustment, return to the initial screen by pressing the (END) button 3 times. -If the throttle stick is moved to the set position while `READY' is flashing, the throttle servo will move to the set position. The throttle operation wait state is reset when the throttle stick is returned. -When using the Start function, always set the function by performing step 3 above each time. READY setting OFF : off state READY: Ready state ACT : on state Start Function, Engine Cut/AT-START(Throttle system) Functions 53 Engine Cut function adjustment (Preparation) - Use the function select switch function (page ) to select the switch. - Select setup item "PRST" and make the following adjustments. Setup item switching - Use the (DN) or (UP) button to switch the setup item. Setup items PRST : Preset position MODE : Function selection 1 (Preset position setup) Use the (+) and (-) buttons to set the preset position of the throttlle servo. "B100" ~ "B1" : Brake side "0" : neutral "F1" ~ "F100" : Forward side Preset position B100 ~ B1, 0, F1 ~ F100 Initial value: 0 2 When ending adjustment, return to the initial screen by pressing the (END) button 3 times. Adjustment buttons - Use the (+) and (-) buttons to make adjustments. 1 sec) to return to the initial screen. Engine Cut by Boat Mode In case of using Engine Cut Function for boats and the alike, the preset position you set here will be the base point. Set the linkage so that the carburetor will completely close and stop the engine within the adjustable range of the preset. And then adjust the Full Throttle Position by the End Point Adjuster Function at "TH-FWD" side (See page 36). The Idling Position is adjustable by the Throttle Trim. 54 Functions Servo Throw The throttle servo operating position (preset position) set by this setting is unrelated to the setting of other functions. How- Operation Display When this function is activated, the LED flashes. If the power switch is turned on while the idle-up switch is on, an audible alarm will be heard. Immediately set the Preset switch to OFF. ( Warning display) Start Function, Engine Cut/AT-START(Throttle system) Brake mixing/BRAKE MIXING (Throttle, 3rd channel system) Use this mixing when the front and rear brakes must be adjusted independently such as 1/5GP cars, etc. This mixing uses the 2nd channel to control the rear brakes and the 3rd channel to control the front brakes. It is possible to adjust the Brake Return Amount (ABP), Delay Amount (DLY) and Cycle period (CYC) exclusively for the front brake (the 3rd CH). Function at the front side even if the A. B. S Function is off for the rear brake (2nd CH). You can use the same procedure as the 2nd CH " A. B. S Function for setting the Cycle Period (CYC), Duty Ratio (DTY) and Steering Mixing (STM). When the ON/OFF switch of the A. B. S Function is set by the Function Select Switch, the A. B. S. Function will turn on or turn off both the front and rear brakes simultaneously. Operation - When braking, mixing is applied to 2nd channel 3rd channel. - 3rd channel brake rate, delay amount, 3rd channel brake-EXP and 3rd channel brake-A. B. S possible. Button trim setup The function select trim function can control 3rd channel brake rate (BKRT), delay amount (DLY), and 3rd channel brake-A. B. S return amount (ABP) . . . etc setting using button trim BT1 and BT2 and dial trim DL3. (See page 80) Calling the setup screen * Calling from menu screen (Initial screen) Use the or button to select the menu screen. [. . . ] in the Data Pac was called and the Data Pac is not installed, an audible alarm will sound and "SELECT ERROR" will be displayed on the LCD screen. 1 will be forcibly called. 107 LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) Data Pac Error If data transfer with the Data Pac was not performed normally, an audible alarm will sound and "ACCESS ERROR" will be displayed on the LCD screen. - To stop the alarm, turn off the power. If the alarm is not generated, there is no problem. LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) Memory Error If the data in the transmitter is not transferred normally when the power is turned on, an audible alarm will sound and "ACCESS ERROR" will be displayed on the LCD. - To stop the alarm, turn off the power. If the alarm is not generated again, there is no problem. LCD screen: Audible alarm: Tone sounds (7 times) and stops (repeated) 108 Reference Idle-Up or Preset Warning LCD screen: When the power switch is turned on while the idle-up or preset (engine cut) function switch is on, an audible alarm will sound and "MIX WARNING" will be displayed on the LCD. [. . . ]